Snap N Save Sliding Transfer Bench with Molded Seat and Back
Snap N Save Sliding Transfer Bench with Molded Seat and Back

Snap N Save Sliding Transfer Bench with Molded Seat and Back

Authorized Retailer Badge
  • HyGiene Products
  • Non Returnable
  • Latex Free

Snap N Save Sliding Transfer Bench with Molded Seat and Back is very easy to assemble as it requires no tools. Secured safety locks on each side of the bench allow the user to get on the bench safely before sliding to the other side and locking the bench while inside the tub or shower. It has a blow molded plastic seat and back with a textured finish.

Snap N Save Sliding Transfer Bench Highlights

  • Rust Proof
  • Adjustable Height
  • Ideal For Caregivers
  • Anti-Slip Tips
  • Adjustable Safety Belt
  • Latex Free

Note: This item cannot be returned.

Buy this product and earn 8.45 Reward Dollars.

  • Base Length
  • Armrest
  • Taller Legs
  • Total: $280
    Total: $169
Total: $280
Total: $169

Snap N Save Sliding Transfer Bench Features

  • Seat glides smoothly in and out of the bathtub or shower over polished, high-strength aluminum tubes.
  • This bench can be assembled to face either the right or the left (with the side panel with handlebar installed on either the right or left side of the bench).
NOTE: Please measure the bathroom and bathtub or shower dimensions carefully to make sure this product will fit that specific bathroom. This product is a hygiene item and is non-returnable.

How to assemble Snap N Save Sliding Transfer Bench?

  • Step 1. Take the leg frame with the handlebar, and lay it flat on the ground.
  • Step 2. Determine the direction to face the seat in the bathtub. The leg frame with the handlebar will be the side that goes inside the bathtub.
  • Step 3. There are two sliding rails: one rail has 2 brass push buttons, and the other rail has 4 push buttons.
  • Step 4. Take the rail with 4 push buttons, and insert it into the side of the frame you want the seat to face, making sure the two larger push buttons face down, and the two smaller push buttons face outwards (the smaller push buttons are for the sliding rail locking mechanisms). Make sure the larger, bottom button snaps firmly into the frame.
  • Step 5. Insert the other sliding rail into the other side of the leg frame, making sure the button snaps firmly into place.
  • Step 6. Take the seat with the attached sliding rings, and align the sliding rings with the rails, so that the locking side of the seat (the side with the red tabs) is on the same rail as the 4 brass push buttons. Insert both sliding rails into the sliding rings under the seat. Push in the push buttons to slide seat easily onto the rails.
  • Step 7. Take the other leg frame, and insert the sliding rails into it. Make sure the brass buttons snap firmly into place.
  • Step 8. Take the 4 legs, and insert them into the leg frames. Set the bench height by using the same button-hole location for each leg. Make sure the buttons snap firmly into place. For safety, adjust the rubber tips on the legs by turning them outward for maximum floor contact.
  • Step 9. Sit the bench up on the legs. Take the backrest, and press the two brass push buttons on the frame of the backrest. Insert the backrest into the tubes underneath the seat, and push it in until the brass push buttons snap firmly into place.

Cleaning and using Instructions

Safety Belt: For added security and stability, adjust the safety belt around the user’s lap.
Locking Mechanism: Lock the seat into place by making sure the slide ring snaps firmly onto the brass push button at the end of the sliding rail (shown below). Release the locking mechanism by pressing down on the red tab of the locked slide ring.
Sliding Rails: If the seat is not sliding smooth it is recommended spraying WD40 along the sliding rails.
Rubber Tips: Be sure the rubber tips are turned outward for maximum floor contact and stability.
Cleaning: Rinse off the seat area with water after each use to prevent dirt, soap scum, and mineral deposits from forming which could block the push button areas.


ParticularsStandard (61211)Long (61281)X-Long (61291)
Seat Size17.75" x 14.75"17.75" x 14.75"17.75" x 14.75"
Seat Height18.25" to 22.25"18.25" to 22.25"18.25" to 22.25"
Base Lenght39" to 40"43" to 44"48" to 49"
Base Depth18.25" to 20"18.25" to 20"18.25" to 20"
Max Tub Clearance18.5"18.5"18.5"
Back Height from Floor32" to 36.25"32" to 36.25"32" to 36.25"
Sliding Distance15"15"15"
Weight Capacity400 lbs400 lbs400 lbs


LIMITED ONE-YEAR WARRANTY: The Limited Product Warranty only applies for Eagle Health Supplies products purchased from one of our Authorized Dealers for one year from the date of purchase. The Limited Warranty is for parts for manufacturing defects only. The product serial number along with proof of purchase must be provided to your place of purchase. Rental equipment is excluded from warranty. The warranty cannot be transferred. Warranty is invalid if product is modified or altered in any way. Warranty does not cover damage to the product through negligence, accident, misuse, lack of maintenance, improper storage, abuse, tampering, or damage resulting from transit. Such evaluation will be solely determined by Eagle Health Supplies. Further, the warranty shall not apply to problems arising from normal wear and tear or failure to follow product instructions for use and/or assembly. Eagle Health Supplies disclaims any liability for incidental or consequential damages.

Customer Reviews

Questions & Answers


Enter your Answer below.

Security Question: + =
question image
ItemName - now

Your question will show here once it will get approved.
answer image
UserName - now
Your Answer will show here once it will get approved.
Please enter your and your friends email address below.
Fields marked with * are compulsory

The selected product information has been successfully emailed to your friend.

Thank you for using