How to use Innospire Go Portable Mesh Nebulizer?
Three Easy Steps To Use Innospire Go Portable Mesh Nebulizer
Step 1. Fill Simply lift the green lid and pour in the medication. Close the lid and make sure youre sitting up straight, ready for therapy.
Step 2. Treat Press the on button and breathe in and out through the mouthpiece. InnoSpire Go will indicate therapy completion with audible and visible signals - before turning itself off.
Step 3. Clean After each treatment remove the mouthpiece and rinse it in warm water. At the end of each day wash it in warm soapy water and once a week disinfect it in boiling water.
How to use your InnoSpire Go
Step 1. After unpacking the nebulizer check you have all the items listed and that there is no visible damage or defects. Contact your product distributor or Philips customer service if anything is missing or damaged. Prior to first use clean the mouthpiece assembly as per the cleaning instructions and fully charge the battery. Ensure the device is disconnected from the power during assembly and disassembly
Step 2. Check the nebulizer and accessories are clean (free of debris), dry and not damaged prior to use.
Step 3. Attach the mouthpiece assembly to the handset. Do not use separate mask adapter as a mouthpiece.
Step 4. Lift the green medication chamber lid.
Step 5. Empty the contents of the medication vial into the medication chamber.
- The maximum fill volume is 8ml and this is shown by the word MAX on the protrusion below the hinge. Do not fill medication above this level.
Step 6. Close the lid to the medication chamber.
Step 7. If using a mask, attach the mask adapter to the mouthpiece assembly and attach the mask to mask adapter.
Step 8. If you are using the power adapter to power the nebulizer, plug the cable into the socket on the handset and plug the adapter into the wall outlet.
Step 9. Press the on/off button on the handset to switch the nebulizer on and begin nebulization.
Step 10. Check the battery level.
- If the LED is SOLID GREEN the battery is charged.
- If the LED is SOLID AMBER, there is enough charge for at least one more treatment. Please charge your nebulizer after your treatment.
- If the LED FLASHES AMBER and then switches off there is not enough charge to take a treatment.
- If the LED does not illuminate, please refer to the troubleshooting section of this manual.
Step 11. Ensure aerosol is coming out of the mouthpiece assembly or mask.
Step 12. a)
If using the mouthpiece, hold the handset in your hand and place the mouthpiece between your teeth with your lips sealed around it. Breathe normally through your mouth.
b)
If using a mask, hold the handset in your hand and gently press the mask against your face and breathe normally through your mouth. During use, some aerosol will be emitted from the back of the mouthpiece assembly
Do not tilt the device in any direction more than 45 degrees during the course of a treatment as this will prevent the nebulizer from completely nebulizing all the medication in the chamber.
Step 13. If you need to take a rest, press the on/off button to stop your treatment. To continue your treatment press the on/off button again.
Step 14. Your treatment is finished when the nebulizer beeps and the LED flashes. The device will turn off automatically.
Step 15. Check the medication chamber for residual medication. If there are more than a few drops remaining, press the on/off button again to continue your treatment.
Step 16. Clean the nebulizer following the cleaning instructions.
Charging the battery
Step 1. Connect the power adapter to the socket on the back of the handset.
Step 2. Plug the other end of the power adapter into the wall outlet.
Step 3. The LED will
PULSE GREEN.
Step 4. Charge the battery until the LED turns
SOLID GREEN indicating it is fully charged.
Step 5. Unplug the power adapter from both the handset and the wall outlet. It is recommended to unplug the power adapter once the battery is fully charged to preserve battery life
Cleaning and maintenance
- After each use
- Pour away residual medication from the medication chamber.
- Press the mouthpiece assembly release button to separate the mouthpiece assembly from the handset.
- Rinse the mouthpiece assembly thoroughly under running tap water.
- Shake off excess water and allow to air dry fully before storing.
- Daily cleaning
- Wash the mouthpiece assembly by hand in a bowl of warm soapy water (liquid dish washing soap) for 2 minutes.
- Rinse the mouthpiece assembly thoroughly under running tap water.
- Shake off excess water and allow to air dry fully before storing.
Weekly disinfection
CAUTION: Risk of scalding. Use care around boiling water and in handling hot parts.- Prior to disinfection, ensure all parts are visibly clean and free from dirt/debris. Boil the mouthpiece assembly in water for 10 minutes. Ensure the medication chamber lid is open and there is enough water in the pan to prevent the mouthpiece assembly from touching the bottom or boiling dry. Shake off excess water and allow to air dry fully before storing.
- Immerse the mouthpiece assembly in a disinfectant of the Gluteraldehyde group (testing performed with Korsolex Extra, 4% for 15 minutes). Rinse thoroughly according to manufacturers instructions.
- Mask cleaning
- Wipe your handset clean with a clean damp cloth weekly or as needed. Do not use other cleaning methods or solutions.
- Handset cleaning- If using a mask and mask adapter, once a week: agitate for 2 minutes or soak for 10 minutes, in warm soapy water (liquid dishwashing soap), rinse thoroughly under running tap water and air dry fully.
- After each cleaning procedure visually inspect for any remaining dirt/debris, if any remains repeat the procedure. Visually inspect for any moisture before storing.
