Dynasyst Orfitube Single Adjuster Kit
Dynasyst Orfitube Single Adjuster Kit

Dynasyst Orfitube Single Adjuster Kit

Brand/Manufacturer: ORFIT INDUSTRIES
Save

Dynasyst Orfitube Single Adjuster Kit is a structural unit for placing onto a hand orthosis, in order to give the orthosis added adjustable and dynamic action. The compact design allows the user to fix one individual adjuster for each finger.

Item #DescPkgRewardPrice 
35305 Single Orfitube Adjuster Kit 5/Pack $0.55
$85.65
$54.99

Features

  • Dynasyst Orfitube Single Adjuster Kit puts the user in full control of longitudinal and lateral position of Orfitubes
  • Stainless steel adjusting screw secures the position of the Orfitube in the adjusting ring 
  • Adjusting ring (Polyacetal) holds and allows alterations of the Orfitube
  • Fixation plate fastens and stabilises the adjuster to a splint
  • Adjuster is lightweight
    Click Here For Instruction Guide 

More Information

  • Instructions For Use
    1. Put a basic splint on the patient.
    2. Determine in which plane the suspension point needs to be adjustable.
    3. Find a location on the splint that is ± parallel to this plane
    4. Feed the Orfitube through the Adjuster over the anticipated setting distance and fasten the screw of the adjusting ring.
    5. If the Orfitube ts the orthosis without bending, then continue with item 10. 6. In order to bend the Orfitube, rst introduce the bending rod till beyond the adjusting ring
    7. Bend the Orfitube to the desired angle
    8. Remove the bending rod from the angle and if necessary make additional bends to end up in the adjusting plane again
    9. Completely remove the bending rod from the tube 10. Now slide the Orfitube into the Adjuster up to its most distal position
    11. For a few seconds, heat the underneath of the Orfitube Adjuster as well as the attachment location on the orthosis with a heat gun (watch out for overheating)
    12. Firmly press the Adjuster onto the orthosis in the desired position and allow it to cool down completely.
    Note: after heating, the Adjuster can be adhered to the following splinting materials: :
    - Ort Classic, Orlight  and Tecnot
    - Colort , Soft-Fit and Orlined , provided the “Non Stick” - coating is mechanically removed.
    - It is possible to attach the Orfitube onto other, non-adherent splint materials, by using suitable adhesives
    - In some cases, it may be possible to detach the adjusting ring and screw it directly onto the splint
    13. Cut the Orfitube to length using heavy scissors (or by incision and breaking)
    14. Press the Tube End rmly onto the Orfitube.
    15. Introduce an braided elastic equipped with a nger cuff.
    16. Give the required tension to the elastic. 
  • Adjusting the Orfitube
    - As it should remain possible to vary the elastic’s suspension point during the course of rehabilitation, the Orfitube can be accurately adjusted.
    - By loosening the adjusting screw, the Orfitube can be rotated and/or translated.
  • Maintenance
    - Orfitube Adjuster does not require maintenance.
    - Clean with lukewarm water and soap.
    - It is not possible to sterilise an Orfitube Adjuster in an autoclave, although it can be sterilised using gas sterilisation.
    - It can be disinfected using alcohol.
  • Warnings
    - Do not use an open ame to heat the Adjuster xation plate.
    - Only trained medical personnel should make and apply dynamic orthosis using the Orfitube Adjuster.

Customer Reviews

Questions & Answers


 
 
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*

 
SubmitCancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.healthproductsforyou.com

Close