Smiths Medical Medfusion 3500 Syringe Infusion Pump

Medfusion 3500 Syringe Pump Features

• Post-occlusion bolus reduction removes the possibility of a patient receiving an automatic bolus following an occlusion
• More than 18 delivery mode combinations are available with optional delivery characteristics such as loading dose, bolus dose, flush standby, and more
• A widescreen eliminates the need for acronyms, each medicine name can include up to 30 characters
• The internal battery capacity of 10 hours at 25°C infusing at 5.0mL/hr with a 60mL syringe (with a fully charged battery)
• Biomed setting capabilities for examining service history, viewing PM dates, and obtaining calibration and diagnostic tests
• Mounts easily an I.V. pole, an infant's isolette, or a radiant warmer that may rotate
• Accepts multiple syringe sizes and identifies various syringe types from 1mL to 60mL automatically
• Flow rate accuracy–even with low volume infusions, exceptional infusion accuracy of +/-2 percent
• Ergonomic, easy-to-use, horizontal design shields the entire syringe barrel while allowing single-handed syringe loading
• The back button allows users to go back one step rather than beginning over, making work easier and faster
• FlowSentry monitors pressure-sensing technology that is unrivaled for earlier clinical intervention
• MR Conditional– when fastened to non-movable items, it can be used in static magnetic fields outside the 150 Gauss limit. A 1.5 Tesla 64MHz shielded MRI system was used to conduct the tests

Syringe Infusion Pump Guide Manual

What to buy with Medfusion V6 Syringe Infusion Pump

• Covidien Kendall Monoject Purple Oral Dispenser Syringe
• McKesson Infusion Pump Pouch
• Smith & Nephew IV Prep Antiseptic Wipes

How to use Smith Medical Medfusion Syringe Pump?

1. Firstly, extend the plunger
2. Lock the syringe in and lock the barrel down
3. Make the end of the plunge of the syringe and then press the power button on
4. Select the mode then select the type of syringe you want to insert
5. Press enter to confirm
6. Then select the amount of dose that you want to deliver in an hour
7. Press the bolus key to fill the line that goes to the patient
8. Press the start button
9. The green light will indicate the line that gets included and there's an occlusion message and the unit will alarm and shut down until you relieve it of the occlusion

How to enhance the Syringe Pump Performance?

• Select syringe brands based on best performance
• Use the smallest syringe for the volume of solution being delivered
• It is ideal to use Luer-Lok Tip syringes

How to clean Smiths Medical Infusion Pump?

• Firstly turn the pump off and disconnect from the AC power source
• Use a 70% isopropyl alcohol solution or a 1:6 diluted bleach solution to clean the pump.
• To clean the pump, spray a soft cloth with the cleaning agents and wipe down the pump.
• Do not spray the pump directly as it could cause the cleaning solution to pool and would cause damage to the device and its components.

FAQs About Medfusion Infusion Pump

What are the uses of a syringe pump?

Syringe pumps are used to deliver a very small amount of medications, mechanically moving the piston of a syringe to send medication into IV tubing.

How do you load a syringe with Medfusion 3500 Infusion Pump?

1. Squeeze the syringe plunger release lever on the syringe plunger driver and pull it out gently to extend it all the way outward.
2. Load the syringe onto the pump.

Which medicines are given by syringe pump?

Medicines used in syringe pumps are most often used to treat and relief pain, nausea and vomiting, agitation, secretions and seizures.

What is Medfusion syringe infusion pump?

It is a different type of infusion delivery device. Instead of drawing fluid from an infusion bag, intravenous medications are drawn into a syringe and installed into the device.