Vasyli Custom Red Full Length High Density Insoles

Vasyli Custom Orthotics Full Length Features

Back, Knee, and Heel Pain
Vasyli Custom Red Insoles help relieve heel, knee, or back pain

Walking and Everyday Use
These High-Density Insoles are ideal for walking and everyday use

Athletic Use
Covered in a bonded fabric, they are suitable for athletic footwear

Custom-Fit Shoes
Vasyli Custom Red Insoles are designed for custom-fit shoes

 

Boots
They are appropriate for men's and women's hiking boots

Shoes For Kids
Vasyli High-Density Insoles can be used in shoes for kids

Casual Shoes
Ideal for most men's shoes and broad-fitting, flat footwear for ladies

Custom-Fit
Vasyli Custom Red Insoles are heat-moldable for a custom fit

 

What to buy with Vasyli Insoles

• Count R Force Arch Brace
• Medi-Dyne Tulis Classic Gel Heel Cups
• HeelZup Cloud Heel Suspension Cushion
• Armor1 Ankle Roll Guard For Ankle Sprains

How to use Vasyli Insoles?

Foot Orthosis Fitting Procedure

The primary concern when fitting the orthosis is to ensure that they are comfortable. This is the single most important factor in maximizing participant compliance with wearing the orthosis. Secondly, but nevertheless still importantly, you should aim to achieve a reduction in knee pain during aggravating activities.

Stage 1 - Examine footwear:

• Is it in good condition?
• Do the shoes need replacing i.e. is there a fissuring or breakdown of the sole or midsole?
• Will the shoe be deep enough for the orthosis?
• Is the existing insole easy to remove?
•  
• Is the heel cup firm and vertical?
• Is the last semi-curved i.e. not too straight or curved?

Stage 2 - Size the orthosis:

• Look at the shoe size and match it to the foot orthosis box
• Have the patient stand on the orthosis and check that the leading edge of the arch of the orthosis is approximately 5-10mm proximal to the 1st MTP joint (must allow unrestricted 1st MTP joint function)
• Remove the existing shoe insole
• Insert the orthosis into the shoe
  • Make sure that it fits snugly in the heel cup and does not move around excessively
  • If the leading (distal) edge is uncomfortable, you can use the existing shoe insole to improve this (with permission from the participant)
  • Line up the 3/4 length orthosis with the existing shoe insole, and cut off the distal end of the insole at the level of the distal edge of the 3/4 length orthosis
  • Put the distal end of the insole into the toe of the shoe, and fit the 3/4 length orthosis in behind it
  • This reduces the drop in the leading edge
  • Issue velcro buttons (in practitioner pack) and place them on the bottom of the heel of the orthosis and the heel region of the shoe

Stage 3 - Fit the orthosis:

• Make sure that the participant is wearing socks
• Put the orthosis into the shoes and ask the participant to put their shoes on
  • Ensure that the orthosis is pulled right back to the heel cup and is flush against the medial inner lining of the shoe
  • Use your thumb to hold the 3/4 length orthosis in place as the participant puts their foot in
• Reassess walking/aggravating activity

 Why Vasyli Custom Red Insoles Stand Out?

    • High-Density EVA Construction – Provides firm support and long-lasting durability
    • 6-Degree Rearfoot Varus Angle – Improves biomechanical alignment and motion control
    • Heat-Moldable Design – Customizable fit for personalized comfort
    • Shock Absorption Technology – Poron tear-drop shock dot reduces impact stress
    • Pain Relief Support – Helps alleviate heel, knee, and back pain
    • Versatile Use – Suitable for walking, athletic footwear, boots, casual shoes, and kids’ shoes
    • FSA Approved & Latex Free – Safe, accessible, and cost-effective for most users

Heat Moulding The Orthosis:

• Take the orthosis out of one shoe, leaving the other shoe on 
• Hold the heat gun 10-15cm away from the orthosis, and heat diagonally across the plantar surface of the orthosis just distal to the heel cup (over the writing, avoid the blue wedges) until the writing starts to disappear
• Put the orthosis back in the shoe and have the participant put the shoe back on (laced up)
• Find the subtalar joint neutral by placing your finger and thumb on either side of the talus, and your other hand on the distal tibia
• Guiding from the tibia, have the patient roll back and forth into pronation and supination until you find the point where the talus protrudes evenly on both sides; this is approximately subtalar joint neutral
• Ask the participant to stand with equal weight on both feet, looking straight ahead
• Maintain subtalar joint neutral by keeping your hands in position; hold this for about one minute
• Ask the participant to walk approximately 30 meters (e.g. two lengths of a practice hallway or carpark)
• Leave the orthosis in the shoe and repeat the above steps on the opposite side

Vasyli Red Full Length High Density Insoles FAQs - 

Q1. Who should use Vasyli Custom Red Full Length Insoles?

The individuals who would benefit the most from using Vasyli Custom Red Full Length Insoles are those participating in athletic activities or physical activity, whose feet are under the greatest amount of stress as well as those who require a high degree of biomechanical support to alleviate pain in their heels, knees, and lumbar area (back).

Q2. Can these insoles be customized?

Yes. Vasyli Custom Red Insoles are heat moldable, allowing users or practitioners to shape them for a precise, custom fit using a standard heat gun.

Q3. What types of shoes are compatible with these insoles?

They work well in athletic shoes, walking shoes, hiking boots, casual footwear, custom-fit shoes, and even kids’ shoes, depending on size.

Q4. Do these insoles help with pain relief?

Yes. They are specifically designed to help reduce heel pain, knee pain, and lower back discomfort by improving foot alignment and shock absorption.

Q5. Are Vasyli Custom Red Insoles FSA approved and latex free?

Yes. These insoles are FSA approved and latex free, making them suitable for users with sensitivities and those using flexible spending accounts.