Drive Standard Telescoping Full Length Side Rail
Drive Standard Telescoping Full Length Side Rail

Drive Standard Telescoping Full Length Side Rail

Brand/Manufacturer: DRIVE MEDICAL
Save
Authorized Retailer Badge

Drive Standard Telescoping Full Length Side Rail is constructed of 1-inch steel with brown vein finish that is strong and attractive. It easily adjusts up or down with spring-loaded release and fits most hospital or home care beds to help prevent the patient from falling out of bed. The spring-loaded cross bars are easy to install and remove. Telescopes with movement of the bed to provide adequate support. Includes two telescoping full length bed rails with two cross bars.

Cannot be shipped Next Business Day or Second Business Day delivery.

Item #DescPkgPrice 
15001ABV Brown Vein Finish Pair $99.26 $62.99

More Information

  • Installation
    - Extended onebed rail to reach the head and foot-end crossbraces
    Warning: The outer Telescoping tube of the bed rail must be positioned at the Head-end of the bed to prevent a pinch point when raising/ lowering the bed
    - Insert the outer telescoping rail into the barrel of the Head-end crossbrace
    - Pull and hold the spring loaded knob on the Head-end barrel
    - Adjust the bed rail to one of the three positions
    - Release the spring loaded knob on the Head-end barrel
    - Raise or lower the bed rail until the spring loaded knob clicks securely into the lower or upper adjustment hole or until the rail stop securely rests against the barrel
    - Insert the INNER telescoping rail into the barrel of the FOOT-END cross brace
    - Pull and hold the spring loaded knob on the FOOT- END barrel
    - Adjust bed rail to the position determined in STEP 4
    - Release the spring loaded knob on the FOOT-END barrel
    - Raise or lower the rail until the spring loaded knob clicks securely into the lower or upper adjustment hole or until the rail stop securely rests against the barrel
    - Repeat STEPS 1-11 to install the other bed rail onto the opposite side of the bed
  • Note: Make sure the crossbraces are 45 to 72 inched apart
  • Warning:
    - To prevent damage to levers and motors of articulating beds, make certain that when the foot and head-ends are raised that the telescoping length of the bed rail is not less than 47 inches
    - Otherwise the bed rail has bottomed-out and will bind the drive mechanism of the bed
    - Either the bed rail or the bed will be damaged
  • Caution:
    - Gap between bed rail and mattress when bed is in semi Fowler position. Put rail in MID position to eliminate gapOperating instructionsHold rail, while pulling the spring loaded knob
    - Lower/Raise rail to desired height
    - Release knob and lower/raise the rail until spring loaded knob clicks into position (unless rail is already at lowest position)
    - Repeat STEP 3 for opposite end of bed rail
    - Make sure head and foot-end of bed rails are at the same height

Warranty

Lifetime limited warranty

Customer Reviews

Questions & Answers


 
 
question image
how does this attach to bed?  would it work on a platform bed with a mattress resting on a
frame?  thanks
Linda Schwab - 8/11/2016 5:24:22 PM
facebooktwittergplus
answer image
Thank you for contacting customer care services.
Please refer below link for assembly instructions. 
http://cdn.drivemedical.com/media/files/815/15001ABV_hangtag.pdf
Customer Care - 8/12/2016 1:12:12 AM
question image
Can this attach to most normal bed frames?
Tim - 3/21/2016 8:29:38 PM
facebooktwittergplus
answer image
Yes, it may fit as it is a Standard Telescoping Side Rail.
Customer Care - 3/22/2016 2:30:23 AM
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*

 
SubmitCancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.healthproductsforyou.com

Close