ConvaTec SUR-FIT Natura Two-Piece Moldable White Durahesive Ostomy Skin Barrier

Why Choose 2-Piece Moldable Durahesive Skin Barrier?

• Provides added protection from liquid output
• Simple snap-off, snap-on design allows users to change the pouch quickly to match activities without removing the skin barrier from the skin
• Requires no cutting or measuring, which makes it easy to learn how to use
• A special effect, called turtlenecking, helps create a more secure seal without harming the skin
• The coupling ring provides an audible click confirming a secure connection to the skin barrier
• Gently swell up and hug the stoma, better protecting the skin around the stoma
• SUR-FIT Natura Ostomy Skin Barrier has easy to fit, apply, and remove and features a white collar for increased flexibility
• Starter holes roll back to create the opening for the stoma

What to Buy with White Durahesive Ostomy Skin Barrier?

• ConvaTec SUR-FIT Natura Drainable Pouch With Filter
• ConvaTec AllKare Protective Barrier Wipes
• ConvaTec Eakin Cohesive Paste

How to Use Sur-Fit Natura System?

1. Begin by cleansing the peristomal skin with mild soap and water (soaps should be free of oils and creams).
2. Pat dry thoroughly.
3. The skin should be free of any solvent or greasy substances.

Skin Barrier/Wafer Preparation:

1. Measure the stoma size with the measuring guide provided.
2. Select a skin barrier/wafer with a flange (white ring) that is at least 1/2" (13mm) larger than the widest diameter of the stoma. If this size is not available, go to the next larger flange size.
3. Trace the exact stoma size onto the center white release paper in the back of the skin barrier/wafer.
4. The small starter hole should be in the center of your tracing.
5. Cut along the tracing with curved, short-blade scissors.
6. For skin barriers/wafers with precut stoma opening:
   • Select a skin barrier/wafer with a precut stoma opening the same size as the largest diameter of the stoma.
   • Do not enlarge the precut stoma opening.
   • Remove the white release paper from the skin barrier/wafer.
   • Leave the outer release paper on the tape collar in place.
7. Stomahesive Paste can be applied to the back of the skin barrier/wafer to further fill gaps between the skin barrier/wafer and the stoma.
8. Allow the paste to set for one minute prior to application to the skin. (Do not spread the paste.)

Application of Skin Barrier/Wafer:

1. Center the skin barrier over the stoma.
2. Press the skin barrier against the skin.
3. If using a tape-bordered skin barrier, remove the remaining backing paper one side at a time.
4. During application, maintain gentle pressure on the skin barrier for 30 seconds to improve adhesion.

Attachment of Pouch:

1. Before attaching the pouch, allow a small amount of air to enter the pouch by gently separating it.
2. If you are using a SUR-FIT Natura drainable pouch with a clip, for attachment of the tail clip, fold the bottom of the pouch over the tail clip only once.
3. Press firmly on the center of the clip until it snaps securely closed.
4. If you are using a SUR-FIT Natura urostomy drainable pouch with a tap, make sure the tap on the pouch is closed before attaching the pouch to the wafer.
5. Align the flange on the pouch with the flange on the skin barrier.
6. Press them together beginning at the bottom and circling around the top side of the flange.
7. You will hear several clicks as the system locks into place.

Removal of Pouch

1. To easily remove the pouch from the skin barrier, gently pull downward on the plastic pouch tab and lift the pouch off.
2. Anchor the wafer by holding it down with your other hand.
3. SUR-FIT Natura closed-end pouches:
   Remove and discard as needed. (Do not flush.)
4. Filter covers are waterproof and should be used when bathing or swimming to prevent the filter from becoming wet.
5. Remove the filter cover after patting the pouch dry.

Removal of Skin Barrier/Wafer:

1. Gently pull the skin barrier down, away from the skin, while supporting the adjacent skin with your other hand.
2. To assist with the barrier removal, an AllKare Adhesive Remover wipe may be used to remove any adhesive buildup.