Rolyan Aquaplast-T Watercolors UltraPerf Splinting Material
Rolyan Aquaplast-T Watercolors UltraPerf Splinting Material

Rolyan Aquaplast-T Watercolors UltraPerf Splinting Material

Brand/Manufacturer: PATTERSON MEDICAL
Save
Authorized Retailer Badge

Rolyan Aquaplast-T Watercolors UltraPerf Splinting Material is bright, moldable splinting material for persons with upper or lower extremity disabilities. It is the optimum combination of intimate conformability and resistant stretch. 100% memory allows repeated reheating and economical splint revisions. It has 13% UltraPerf perforation pattern which is ideal for lightweight finger or hand splints requiring breathability.

Item #DescPkgRewardPrice 
550555 Royal Blue Each $2.40
$185.50
$119.90
550556 Royal Blue 4/Pack $7.20
$500.40
$359.90
551492 Lavendar Each $2.40
$185.50
$119.90
551493 Lavendar 4/Pack $7.20
$500.40
$359.90
A962421 Beige Each $2.40
$185.50
$119.90
A96242104 Beige 4/Pack $7.20
$500.40
$359.90
A9631031 Purple Each $2.40
$185.50
$119.90
A96310314 Purple 4/Pack $7.20
$500.40
$359.90
A963241 Charcoal Each $2.40
$185.50
$119.90
A96324104 Charcoal 4/Pack $7.20
$500.40
$359.90
A963461 Electric Blue Each $2.40
$185.50
$119.90
A96346104 Electric Blue 4/Pack $7.20
$500.40
$359.90
A9631131 Red, Sheet Each $2.40
$185.50
$119.90
A963131 Spring Green, Sheet Each $2.40
$185.50
$119.90
A963141 Pastel Blue, Sheet Each $2.40
$185.50
$119.90
A963471 Hot Pink, Sheet Each $2.40
$185.50
$119.90
562841 Forest Green, Sheet Each $2.40
$185.50
$119.90

Features

  • Rolyan Aquaplast-T Watercolors UltraPerf Splinting Material edges trim easily
  • For a temporary bond, pinch heated surfaces together
  • For a permanent bond, remove coating with liquid remover or by scraping with a sharp instrument
  • Controlled stretch allows aggressive or gentle handling of the material
  • Excellent flexibility for applying and removing circumferential splints
  • Dimension: 1/16" x 18" x 24" (1.6mm x 46cm x 61cm)
  • Recommended Uses:
    - Ideal for serial splints
    - Hand, wrist, finger and thumb splints
    - Dynamic outrigger bases

More Information

  • Precautions for Finished Orthoses:
    -
    Splint adjustments are to be made only by a healthcare professional. The healthcare professional is responsible for providing wearing instructions and precautions to other healthcare practitioners, care providers involved in the patients care, and the patient.
    - If unusual swelling, skin discoloration or discomfort occurs, use should be discontinued and a health care professional consulted
  • Patterning:
    - Patterns can be drawn on all splinting materials with a scratch awl before placing the material in the water 
  • Cutting:
    - All splinting materials can be cut at room temperature by using heavy-duty shears, or scoring with a utility knife and bending at the scored mark, then completing the cut with a knife or scissors.
    - If more detailed pattern-making is required, it is recommended that the pattern be transferred to the splinting material to make a rough blank. Then heat the rough blank for one-half the recommended time or until material is soft enough to cut with scissors.
    - This method will reduce rough edges and save time with edge finishing.
    - Light splinting materials can be cut at room temperature using scissors.
  • Heating: For Aquaplast splinting materials, use a heat pan liner in the bottom of the heat pan or frying pan.
    - Hydrocollator units can be used for large pieces of splinting material.
    - Use a heat pan liner to dip the material into the unit, to ensure that the material does not touch the bottom. Do not leave the splint blank unattended.
    - In addition to hot water heating, Aquaplast materials can be heated in a convection oven
    Note: that dry heating makes the material self-bonding, so no surface preparation is required for bonding. Material that is heated in the oven also becomes hotter than material heated in water; check temperature carefully before applying it to the patient. Heat material without overlapping or folding on a baking sheet with a non-stick surface in a preheated oven as follows.
    - heat at 195° to 205°F (90°C to 95°C) for up to 10 minutes or until transparent or translucent
    Technical Tip: To prevent hands from sticking to Original Aquaplast and Original Resilient, use cold cream or mineral oil on hands or dip hands in cold water.
  • Forming:
    - When Aquaplast materials become transparent or translucent in a heat pan, the material is soft and ready to form.
    - When the material is soft, remove it from the water and pat it dry with an absorbent towel. (To avoid towel impressions or lint, cover the towel with a pillow case before drying the splinting material.)
    - Check the temperature of the material before beginning to fabricate the splint on the patient
    Technical Tip: To prevent hands from sticking to Original Aquaplast and Original Resilient, use cold cream or mineral oil on hands or dip hands in cold water
  • Cooling:
    - Cold water, cold packs, cold spray, or cold wraps can be used to speed the cooling process.
    Technical Tip: Exercise band that has been stored in a freezer can also be used to speed the cooling process 
  • Adjustments:
    - Change in contour or design of the splint can be accomplished easily by spot-heating the area by pouring hot water over it or using a heat gun. Care should be taken not to overheat the material when using a heat gun
    - keep the hot air stream of the heat gun moving and do not hold it too close to the material.
  • Edge Finishing:
    - Smooth edges by heating the rough edges of the splinting material with a heat gun or dipping the edge into heated water for 5 to 10 seconds.
    - Smooth the heated edges using finger tips or the palm of the hand small amount of hand or body lotion on the finger tips makes smoothing the edges easier.
  • Care and Cleaning:
    - Splinting materials The shelf life of low-temperature splinting materials is indefinite under the following conditions:
    - Store at temperatures between 40° and 90°F (4° and 32°C)
    - Store at less than 65% relative humidity
    - Avoid prolonged exposure to light, especially ultraviolet light
    - Avoid exposure to corrosive fumes and ethylene oxide fumes.
  • Fabricated splints:
    - The splint will lose its shape in temperatures over 135°F (57°C). It should be kept away from sources of heat such as ovens, hot water, open flames, and sunny car windows.
    - The splint can be cleaned with soap and lukewarm water.
    - The straps can be washed with soap and water, but the adhesive portion should not be moistened.
    - The splint and straps should be allowed to dry thoroughly before reapplication of the splint.

Customer Reviews

Questions & Answers


 
 

Enter your Answer below.

Security Question: + =
question image
ItemQuestion
ItemName - now

Your question will show here once it will get approved.
answer image
UserAnswer
UserName - now
Your Answer will show here once it will get approved.
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*

 
SubmitCancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.healthproductsforyou.com

Close