Medline EvenCare G2 Blood Glucose Monitoring System

Evencare G2 Blood Glucose Meter Features

• Memory option: Stores 300 test times and can provide 7-, 14- and 30-day averaging
• Small blood sample size: 1 μL
• No coding required: This glucose monitor minimizes errors and inaccurate results
• Easy to use: Voice assistance guides you through the testing process and provides results in either English or Spanish
• Alternate site testing: Option to test on the forearm, palm, or fingertips
• Fast test time: Results in 6 seconds
• Alarm option: Set reminders for up to 3 different times

Evencare G2 Blood Glucose Meter SDS

Evencare G2 Meter Parts

• A - Test Strip Port: Insert test strip
• B - Meter Display: This Shows your blood glucose test results, memory values, averages, and other messages.
• C - Switch Button: Press and hold Enter for 2 seconds to turn on or off the meter. Press Enter to go into setup mode when not testing. Press ▲or▼ enter control mode with the test strip inserted, during meter setting, or to navigate the stored test values and averages

 

Evencare Glucometer User Guides

• EvenCare G2 Control Solution Test
• Evencare G2 Blood Glucose Meter User Manual
• Operators Manual

What to buy with Glucose Monitoring Devices

• Medline EvenCare G2 Glucose Meter Test Strips
• Simple Diagnostics Clever Choice Control Solution
• Medline Safety Lancets

How to perform Blood Glucose Tests with this Device?

1. Take an EVENCARE G2 Test Strip from the test strip bottle and close the bottle immediately. Insert the test strip to turn on the meter.
2. Wait for a flashing blood drop and an arrow icon on the meter display screen. The meter will also announce, “Please apply blood onto the test strip” if you have the voice feature turned on.
3. Obtain blood sample.
   • For Fingertip Testing:
     • Hold the lancing device (use the white adjustable cap or safety lancet) against the side of your fingertip and press the release button to create a puncture.
   • For Testing on Palm and Forearm:
     • Hold the lancing device (use the clear adjustable cap) against the test site (base of palm or forearm). Avoid a test site with veins, moles, excessive hair, or bone.
     • Press the lancing device firmly against the test site and press the release button, do not lift up the lancing device.
     • For forearm test sites, apply and release pressure (“pumping”) for a few seconds while keeping the lancing device in constant contact with the skin. Palm testing (at the base of the thumb) does not require pumping. When the blood is approximately ( ) size, lift the lancing device straight up without smearing the blood.
4. Gently bring the test strip and touch the drop of blood at a slight angle. The test strip acts like a straw to pull the blood in. Keep the test strip in the blood drop until the meter beeps to indicate the test strip has enough blood to test.
5. The screen will start to count down. After 6 seconds, your blood glucose result will appear on the meter display screen and be announced verbally if the voice feature is turned on. Your test result will be automatically stored in the meter memory.
6. Properly discard the used test strip. The meter will turn off automatically.
7. Remove the used lancet from your lancing device according to instructions and discard it into a proper waste container.

Cleaning and Disinfecting the Glucometer

1. Wash hands with soap and water and dry thoroughly.
2. Inspect for blood, debris, dust, or lint anywhere on the meter or lancing device.
3. To clean the meter, use a moist (not wet) lint-free cloth dampened with a mild detergent. Wipe all external areas of the meter or lancing device including both front and back surfaces until visibly clean. Avoid wetting the meter test strip port.
4. To disinfect your meter, clean the meter with one of the validated disinfecting wipes listed below. Other EPA-registered wipes may be used for disinfecting the EVENCARE G2 system, however, these other wipes have not been validated and could affect the performance of your meter. Wipe all external areas of the meter or lancing device including both front and back surfaces until visibly clean. Avoid wetting the meter test strip port. Allow the surface of the meter or lancing device to remain wet at room temperature for the contact time listed on the wipe’s directions for use.
5. Wipe the meter dry or allow it to air dry.
6. Wash hands with soap and water and dry thoroughly.

Storage and Precautions:

• Handle the meter carefully - severe shock, such as dropping the meter, could damage the electronics.
• The meter and test strips are designed to be used within the temperature ranges between 50˚F to 104˚F.
• Avoid leaving the meter in extremely hot or cold places, such as near a heat source or in an extremely hot or cold car.
• Do not store or use the meter or test strips in high humidity levels, such as bathroom or kitchen.
• Always close the bottle cap immediately after removing a test strip and close it tightly.
• Do not take the meter apart as doing so will void the warranty.