3B Medical Siesta Nasal CPAP Mask With Headgear

Why to buy Siesta Nasal Mask?

• New Headgear Design: Holds the mask gently in place while preventing strap marks.
• Modern Mask Technology: Easy change cushion cup that snaps into place and self adjusts to the patient’s face.
• Freedom of Movement Full: 360° swivel port.
• Ergonomically Designed: Modern design and clean lines define the new Siesta Nasal mask. One of the most petite and flexible masks on the market.

When to use 3B Medical Siesta CPAP Mask

The Siesta Nasal Mask channels airflow non-invasively to the patient from a positive airway pressure device such as continuous positive airway pressure (CPAP) or bi-level system.
The Siesta Nasal CPAP Mask is:

• To be used by adult patients (> 66 lb / 30 kg) for whom positive airway pressure therapy has been prescribed.
• Intended for single patient use.

What to buy with Siesta Nasal Mask

• 3B Medical Luna II QX CPAP With Integrated Heated Humidifier
• 3B Medical CPAP Wipes
• Maril Control III Disinfectant CPAP Cleaning Solution

How to use Siesta CPAP Mask?

Fitting the Siesta CPAP Mask

1. Attach the headgear straps by threading them through the forehead frame and clips gaps. 
2. Hold the mask over your nose and pull the headgear over your head. 
3. Bring the lower headgear straps below your ears, connect the clips to the frame assembly. 
4. Adjust the upper headgear straps evenly until they are comfortable and secure, and reattach the mask. 
5. Adjust the lower headgear straps evenly until they are comfortable and secure, and reattach the mask.
6. Now mask is ready to be worn.

Siesta Mask Fitting Template

Disassembling the Siesta Nasal Mask

• Undo and remove the upper headgear straps out of the slots on the frame.
• Remove the cushion assembly from the frame assembly.
• Remove the short tube from the frame assembly.

How to Reassemble the Siesta Mask?

• Install the short tube onto the frame assembly and confirm that the swivel is securely attached.
• Install the cushion assembly onto the frame assembly and confirm that the cushion assembly is securely attached.
• Install the upper-half of the headgear onto the upper slot of the frame assembly.

Cleaning the 3B Medical Siesta CPAP Mask?

• The mask and headgear can only be cleaned through hand washing or placed in the lumin device.
• The headgear may be washed without removing the clips
• When washing the mask, the elbow and the frame cannot be disassembled from the frame assembly.
• Always follow cleaning instructions and do not use solutions containing bleach, chlorine, alcohol, aromatics, moisturizers, antibacterial agents, or scented oils to clean any part of the system or air tubing, otherwise may damage the mask.
• Exposing any part of the system or tubing to direct sunlight or heat may cause deterioration.
• If any visible deterioration of the component is apparent (cracking, crazing, tears etc) the component should be discarded and replaced.

How to care for Siesta Nasal Mask

Daily/ After each use:

• Disassemble the mask components according to the disassembly instructions.
• Thoroughly clean the separated mask components (excluding headgear), by gently rubbing in warm (approx. 30°C) water using mild liquid detergent (e.g., Alconox diluted at 1%) for up to 10 minutes.
• Use a soft bristle brush to clean the vent.
• Rinse all components well with drinking quality water and allow to air dry out of direct sunlight.
• When all components are dry, reassemble according to the reassembly instructions.

Weekly Care Instructions

• Handwash the headgear and all components in warm (approx. 30° C) and mild liquid detergent (e.g., Alconox diluted 1%) for up to 10 minutes. Rinse the components well with quality drinking water and allow them to air dry out direct sunlight before assembling.

Siesta Nasal CPAP Mask User Manual