Online since 2002 |   866-316-0162

Rolyan Aquaplast-T Watercolors Electric Blue Splinting Sheet

Authorized Retailer
Product Option

1/16" x 18" x 24" Single Sheet Solid

SKU A96340
$160.29 Each

3/32" x 18" x 24" Single Sheet Solid

SKU 560492
$194.19 Each
Request quote

Rolyan Aquaplast-T Watercolors Electric Blue Splinting Sheet is a moldable splinting material which has the optimum combination of intimate conformability and resistant stretch. 100% memory allows repeated reheating and economical splint revisions. Resoften the material and it will return to its original size and shape.


Total: $160.29

Earn $4.81 in HPFY rewards


  • Rolyan Aquaplast-T Watercolors Electric Blue Splinting Sheet with 19% OptiPerf perforation pattern provides superior ventilation for comfort while maintaining material strength
  • Edges can be trimmed and finished easily
  • For a temporary bond, pinch heated surfaces together
  • For a permanent bond remove the coating with spirits or by safely scraping with a sharp instrument
  • Latex free

More Information

  • Precautions for Finished Orthoses:
    Splint adjustments are to be made only by a healthcare professional. The healthcare professional is responsible for providing wearing instructions and precautions to other healthcare practitioners, care providers involved in the patients care, and the patient.
    - If unusual swelling, skin discoloration or discomfort occurs, use should be discontinued and a health care professional consulted
  • Patterning:
    - Patterns can be drawn on all splinting materials with a scratch awl before placing the material in the water
  • Cutting:
    - All splinting materials can be cut at room temperature by using heavy-duty shears, or scoring with a utility knife and bending at the scored mark, then completing the cut with a knife or scissors.
    - If more detailed pattern-making is required, it is recommended that the pattern be transferred to the splinting material to make a rough blank. Then heat the rough blank for one-half the recommended time or until material is soft enough to cut with scissors.
    - This method will reduce rough edges and save time with edge finishing.
    - Light splinting materials can be cut at room temperature using scissors.
  • Heating: For Aquaplast splinting materials, use a heat pan liner in the bottom of the heat pan or frying pan.
    - Hydrocollator units can be used for large pieces of splinting material.
    - Use a heat pan liner to dip the material into the unit, to ensure that the material does not touch the bottom. Do not leave the splint blank unattended.
    - In addition to hot water heating, Aquaplast materials can be heated in a convection oven
    Note: that dry heating makes the material self-bonding, so no surface preparation is required for bonding. Material that is heated in the oven also becomes hotter than material heated in water; check temperature carefully before applying it to the patient. Heat material without overlapping or folding on a baking sheet with a non-stick surface in a preheated oven as follows.
    - heat at 195° to 205°F (90°C to 95°C) for up to 10 minutes or until transparent or translucent
    Technical Tip: To prevent hands from sticking to Original Aquaplast and Original Resilient, use cold cream or mineral oil on hands or dip hands in cold water.
  • Forming:
    - When Aquaplast materials become transparent or translucent in a heat pan, the material is soft and ready to form.
    - When the material is soft, remove it from the water and pat it dry with an absorbent towel. (To avoid towel impressions or lint, cover the towel with a pillow case before drying the splinting material.)
    - Check the temperature of the material before beginning to fabricate the splint on the patient
    Technical Tip: To prevent hands from sticking to Original Aquaplast and Original Resilient, use cold cream or mineral oil on hands or dip hands in cold water
  • Cooling:
    - Cold water, cold packs, cold spray, or cold wraps can be used to speed the cooling process.
    Technical Tip: Exercise band that has been stored in a freezer can also be used to speed the cooling process
  • Adjustments:
    - Change in contour or design of the splint can be accomplished easily by spot-heating the area by pouring hot water over it or using a heat gun. Care should be taken not to overheat the material when using a heat gun
    - keep the hot air stream of the heat gun moving and do not hold it too close to the material.
  • Edge Finishing:
    - Smooth edges by heating the rough edges of the splinting material with a heat gun or dipping the edge into heated water for 5 to 10 seconds.
    - Smooth the heated edges using finger tips or the palm of the hand small amount of hand or body lotion on the finger tips makes smoothing the edges easier.
  • Care and Cleaning:
    - Splinting materials The shelf life of low-temperature splinting materials is indefinite under the following conditions:
    - Store at temperatures between 40° and 90°F (4° and 32°C)
    - Store at less than 65% relative humidity
    - Avoid prolonged exposure to light, especially ultraviolet light
    - Avoid exposure to corrosive fumes and ethylene oxide fumes.
  • Fabricated splints:
    - The splint will lose its shape in temperatures over 135°F (57°C). It should be kept away from sources of heat such as ovens, hot water, open flames, and sunny car windows.
    - The splint can be cleaned with soap and lukewarm water.
    - The straps can be washed with soap and water, but the adhesive portion should not be moistened.
    - The splint and straps should be allowed to dry thoroughly before reapplication of the splint.

Customer Reviews


{{x.ShortDescription}} ...


Please enter your and your friends email address below.

Fields marked with * are compulsory

Your Name*
Your Email Address
Friend's Name*
Friend's Email Address
The selected product information along with Reward Dollar coupon code has been successfully emailed to you and your friend.

Thank you for using