Ossur CTI Mission Knee Brace

Features of CTI Mission Knee Brace

• Motion Control Hinge - mimics the anatomical motion of the knee to provide progressive motion control
• Flexible Cuffs conform to various leg shapes and muscle movements for comfort and ease of motion
• Antimicrobial Frame Liners enhance comfort, prevents odor and help prevent brace migration for faster recovery
• The ‘Quick-Loc Clip System’ & low-profile straps anchor the brace to the leg quickly and easily
• Ossur Knee Support has easy-to-use spare parts and accessories
• Each brace comes standard with a thick and thin condyle pad set, three pairs of tool-free extension stops (5-10, 10-20, and 20-30) and one set of tibial shims
• Sleek and strong frame made of advance composite material for a lightweight, low-profile design while maintaining maximum strength
• Available in 5 sizes, right and left

When to use CTi Mission Knee Supports?

• Rotary and combined instabilities
• Anterior Cruciate Ligament instability
• Posterior Cruciate Ligament instability
• Medial Collateral Ligament instability
• Lateral Collateral Ligament instability
• Prophylactic use

What to buy with Ossur CTI Mission Knee Support

• Ossur Techform Premium 3 Inch Casting Tape
• Sunmark Aspirin Pain Relief Chewable Tablet
• Ottobock Genu Therma Knee Sleeve Without Patella

How to Apply Ossur Knee Support Brace?

1. To start, first sit down with your knee bent to around 90 degrees. Place the brace on your leg with the hinges on the side of your knee so they points straight ahead. The hinge should be positioned above the centre of your knee.
2. Fasten the strap below the knee first. Feed the strap through the slot and attach the hook-and-loop strap.
3. Attach the lowest strap.
4. Next fasten the strap above the knee.
5. Lastly attach the top strap clip.
6. All Straps should feel firm, yet comfortable.

How to Adjust Ossur CTi Mission Knee Brace?

1. Use any combination of the Condyle pads supplied to widen or narrow the width of the brace at the knee.
2. Control the strap length by adjusting the medial/inside hook-and-loop strap end.
3. The hinge absorbs shocks and forces on the knee, with extension stops available for 5–10°, 10–20° and 20–30°.
4. Match the letter on the extension stop insert with the letter on the inside of the hinge for the correct fit.
5. Tibial wedge pads can be installed to fill in any gaps around the tibia and achieve the desired fit.
6. To add a wedge pad, pull the lower frame liner away from the brace frame and connect the wedge pad as needed (medial, lateral or both) to the liner using the hook fastener.
7. Fine tune the wedge pad position until your brace fits snugly against the tibia.

How to Remove CTi Knee Brace?

• To remove the brace, undo each strap
• Ensure to touch the hook-and-loop tab back onto the strap.
• This will make it easier when fitting the brace next time and will prolong the life of the straps.

How to Replace Ligament of Mission Knee Brace?

1. First remove the bottom screw off the hinge using the provided tool.
2. Pull out the lower frame.
3. Slide down the hinge housing.
4. Remove the upper screw to set the ligament free.
5. Replace it.
6. To reassemble, just repeat the steps in the opposite order.

How to Clean CTi Mission Knee Brace?

• Hand wash using mild detergent and water.
• Air dry only.
• Inspect the brace for obvious signs of wear and fatigue.
• If brace is used in salt water or chlorinated water, rinse well and air dry.

Ossur CTi Mission Knee Brace User Manual

Reasons to buy from HPFY

• Customer care available 24/7 on chat
• Safe and Secure shopping
• Flexible Payment Options
• Authorized Retailer of most reputed brands in medical supplies and equipment