Smirthwaite Mobi Shower Trolley

Smirthwaite Mobi Shower Trolley Features

• Smirthwaite Mobi Shower Trolley is mobile and easy to manoeuvre
• Height adjustable
• Unique stowaway side rails
• Soft comfortable mattress
• Wedge shaped pillow
• Drainage hose
• Suitable for use with a wide number of hoists
• Mains and battery powered
• Sturdy stainless steel construction
• Mobi Shower Trolly User Guide

Instructions for Use

• Safety Instructions
  - The user should NOT be left unattended whilst in the shower trolley. Always ensure a responsible therapist or carer is in attendance
  - The Mobi shower trolley height should NEVER be adjusted without a carer in attendance
  - DO NOT install the wall mounted charger unit in a wet room environment
  - The shower trolley should NOT be used as a transit system
  - Always keep this product away from naked flames, cigarettes and sources of heat including open fireplaces, radiators and heaters
  - Regular maintenance checks and cleaning are essential for the safe use of this 
• equipment (see care and maintenance section)
  - DO NOT fit parts or accessories of other manufacturers to this product unless authorised to do so in writing by G&S Smirthwaite Ltd. Failure to follow these instructions will not only invalidate the guarantee but could make the product dangerous to use. G&S Smirthwaite Ltd will not accept liability for any injury or damage incurred through such malpractices. Any repairs required must be carried out by G&S Smirthwaite Ltd authorised personnel
  - If any part is loose, damaged or functioning incorrectly, DO NOT use until rectified
  - The Mobi shower trolley is CE marked. This certifies that it meets all relevant European safety requirements
• Unpacking
  - When delivered, the trolley will be at its minimum height, the safety sides will be stowed under the bench; the safety ends will be stored upside down and the liner will be folded (see drawing below)
  - Please take note of any instructions on the packaging/box when unpacking. • Place the trolley on the floor with the castors locked
  - Check section 2.0 to confirm all parts/items have been delivered
  - If any part is loose, damaged or functioning incorrectly – do not use until rectified
• Setting Up And Adjusting
  Electrical System Reference
  - The changer is supplied with a control box (mounted to the end of the lower frame), a rechargeable battery and a wall mounted charger
  - The wall mounted charger MUST NOT be situated in a wet room environment
  - A mounting bracket is provided to assist with the mounting of the charger in a suitable position
  - The wall mounted charger is powered by a 100-240V AC 50/60Hz supply
• How to charge
  - The rechargeable battery can be un-clipped from the main control box assembly on the Changer and placed onto the wall mounted charger
  - A green light on the charger will indicate the charger is connected to the AC mains supply
  - A second light will light in yellow when the battery is being charged
  - For routine use, the battery should be charged daily, for a period of 4 hours
  - An audible alarm will sound when the battery has discharged to approximately 25% charge level through use
  - Sufficient charge is held in the battery in reserve to permit emergency lowering of the bed
• Control Box
  - An emergency stop button (RED) is situated on the control box; when depressed this halts the operation of the bed – to enable the Changer to operate again, simply twist the emergency stop button to reset
  - Duty cycle: Max 10% (or 2 minutes) continuous use, then 18 minutes without use
  - The control box system has been designed for operating ambient temperature of +5° C to +40° C
• Positioning The Safety needs
  - Depress spring pins
  - Remove safety end
  - Turn safety end over
  - Re-attach as in drawing
  - Ensure spring pins reengage
  - Repeat steps for opposite end of trolley
• Raising The Safety Needs
  - Pull the safety side fully outwards
  - Swing it to the vertical position
  - Lift it up fully, and allow it to drop a small distance, locking it into the vertical position
  - Repeat for the second safety side
• Unfolding The Liner
  - Raise the trolley to maximum height using the handset
  - Unfold the sides of the liner
  - Secure the sides by using the press studs
• Connecting the Outlet Pipe
  - Screw the pipe on to the nozzle under the liner 
• How To Use
  Wheelchair transfer
  - Lift the safety side up and swing to horizontal position
  - Stow the safety side under the table
  - Lower the table to height of the wheelchair seat
  - Unfasten the press studs on one side of liner
  - Allow liner to drop down
  - It is now possible to transfer the user onto the trolley
  Hoist transfer
  - Transfer patient onto table
  - Ensure liner and safety sides are in the up position
• Care and maintenance
  - To clean the liner and base, use a damp soft cloth with mild soap
  - Rinse with clean cloth and water
  - DO NOT soak/immerse the liner in the water
  - DO NOT use solvents, abrasives, synthetic detergents and wax polishes
  - ALWAYS wipe dry after use
  - ALWAYS keep this product away from naked flames, cigarettes and sources of heat including open fireplaces, radiators and heaters
• Maintenance checks
  Daily checks
  - Check that the battery is fully charged
  - Check the accessories for damage or loose connection points
  - Check all upholstery for signs of wear and tear
  - Check the castors are funning freely and brakes are in full working order
  - Keep the upholstery, wooden and metal parts clean
  - Check that all clamping and positional components are working, secure and free from damage
• Monthly checks
  - Repeat daily checks
  - Additionally, check all mechanical movements operate fully
  - Additionally, check structure for signs of damage or wear and tear