Pride Jazzy Elite ES Power Chair

Features of Pride Mobility Jazzy Elite ES Power Chair

• 24.75" turning radius
• Up to 13.5 miles per charge
• In-line, front-wheel drive technology provides tight turns around corners
• Pride FDA Class II Medical Devices are designed to aid individuals with mobility impairments
• Comfortable, depth-adjustable, limited recline high-back seat with headrest
• 40-apm, PG GC 3 controller
• Optimal indoor maneuverability in small spaces
• Large front wheels for extra absorption over obstacles

Pride Jazzy Elite ES Power Chair Parts

1. Seatback
2. Armrest
3. Controller
4. Seat Base
5. Main Shroud
6. Anti-tip wheel
7. Front rigging (foot platform shown)
8. Drive Wheel
9. Seat Release Lever (optional)
10. Caster wheel
11. Power base assembly
12. Seat assembly

 

What to buy with Jazzy Elite ES Wheelchair

• Guldmann Wide Plain Ramp
• Graham-Field Single Release Folding Walkers - Standard Rubberized PVC Grip
• Sammons Preston StandEasy Chair Lift

How to use Jazzy Elite ES Portable Wheelchair?

To install the seat:

1. Adjust the seat post to the desired position and insert the bolt through the seat post and secure with the nut.
2. Ensure that the hardware on the seat post weldment is tightened to prevent movement in the seat post.
3. Slide the seat down onto the seat post.
4. Install the controller into one of the armrests. Tighten the setscrew with the supplied hex key.
5. Lift the armrest straight up, then route the controller harness and secure with wire ties.
6. Plug the controller harness into the connector on the power base.

To change the seat height:

1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Unplug the controller connector(s) from the power base.
4. Remove the seat from the power base.
5. Loosen the hardware at the front of the seat post.
6. Remove the seat height adjustment bolt, washers, and nuts from the seat post.
7. Raise or lower the upper seat post to the desired position.
8. Reinstall the seat height adjustment hardware to the seat post.
9. Tighten the hardware at the front of the seat post.
10. Reinstall the seat.
11. Reconnect the controller to the power base.

To change the position:

1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Unplug the controller connector(s) from the power base.
4. Remove the seat from the power base.
5. Remove the screws and washers from the bottom of the seat plate. See figure 12.
6. Slide the seat plate forward or backward, aligning the holes in the plate with the corresponding holes on the seat base. You must move both sides of the seat forward or backward the same number of holes.
7. Reinstall the screws and washers to the seat plate and tighten the hardware firmly.
8. Reinstall the seat.
9. Reconnect the controller to the power base.

To change the controller position:

1. Turn off the power to the controller.
2. Unplug the controller harness from the power base.
3. Cut the wire tie(s) that secure the controller harness to the armrest and seat.
4. Flip up the armrest so it is perpendicular to the floor.
5. Loosen the setscrew on the controller bracket.
6. Slide the controller out of the armrest.
7. Loosen the setscrew in the other armrest.
8. Place the controller in the other armrest.
9. Tighten the setscrew to secure the controller.
10. Route the controller harness along the seat frame and secure with wire ties. See figure 8.
11. Plug the controller connector into the power base.

To charge the batteries using the off-board charger:

1. Position the front of your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power Chair.”
3. Plug the off-board charger into the off-board charger/programming socket on the controller.
4. Plug the off-board charger into the electrical outlet.

Pride Jazzy Elite ES Power Wheelchair User Guide

• Jazzy Elite ES Safety Guide
• Jazzy Elite ES Portable Lightweight Power Wheelchair Specification Sheet