Winco Adjustable Back Treatment Table

Winco Adjustable Back Treatment Table Features

• Adjustable headrest to enhance patient comfort, angle range: 6-57 degrees
• High strength powder-coated steel frame and medical grade vinyl steel frame are easy to clean
• Heavy gauge expanded vinyl & medium density foam for superior comfort
• Durable foam construction
• Sturdy steel leg frames
• Note:
  - Product will be shipped knocked down and assembly will be required

Winco 8570 Treatment Table User Manual
 

How to Use Winco Adjustable Back Treatment Table?

Assembly Instructions

1. After checking your product for any shipping damage, table needs to be positioned upside-down on the cardboard shipping container, or protective surface. Remove all packing material and hardware that was secured for shipping. Cut tape on corners of box so that cardboard will lay flat while you assemble table.
2. You will find two Welded Leg Assemblies, one is attached to table frames and one is not.
3. Pivot up the attached Welded Leg Assembly, (located on opposite end from the Backrest.)
4. Next, using a Phillips screwdriver, install (2) 1/4-20 x 1-1/2" screws through the upper leg brace of the Welded Leg Assembly into (2) threaded holes in the wood bottom of Upholstered Top.
5. Install the unattached Welded Leg Assembly, on the end near the Backrest, as shown in parts guide. The cross brace needs to be positioned toward "backrest end" of table.
6. Install (2) 1/4-20 x 2-1/2" screws and (2) 1/4-20 nuts to fasten the unattached Welded leg Assembly to the Table Frame Rails. Heads of screws should face the sides of table, for better appearance. Do not fully tighten at this time.
7. Repeat Step 4.
8. Place (4) 1/4-20 x 1-1/2" screws in (4) holes through the lower leg brace of the Welded Leg Assemblies as shown. Heads of screws should face the ends of table, for better appearance.
9. Align Welded Brace Assembly (smoothest side up, when the table is in the upright position) with the (4) screws & holes on both Welded Leg Assemblies and fasten with (4) 1/4-20 nuts.
10. Tighten all fasteners a this time. (including the nuts & screws holding the Welded Leg Assemblies to the Table Frame Rails).
11. Install the four (4) Glide Feet completely into the ends of the Welded Leg Assemblies.
12. The release handle for the adjustable back rest, can be installed on the left or the right table frame rail, depending on user preference.
    - Should you wish to change the release handle mounting location, simply remove the (2) Phillips's head screws that attach the handle to the table frame rail and relocate the handle to the opposite table frame rail and re-install the screws.
13. Using at least two people, turn table upright.
14. Slide the Paper Holder Rod into the (2) Paper Rod Clamps.
15. Adjust one or two of the Glide Feet to level table.

Operating Instructions

• To raise the Upholstered Backrest, pull the black lever on the Remote Release System.
• To lower the Backrest, pull the same black lever with one hand and apply pressure to the Backrest with your other hand until the desired position is achieved, then release the black lever.

General Care and Cleaning

• Periodically inspect tightness of all screws, bolts, and nuts.
• Winco furnishings are built to provide durable reliable service when properly cared for.
• In general all of the products should be Cleaned, Rinsed, Allowed to air dry.
• It is important to note that disinfecting a product is not the same as cleaning the product.
• Disinfectants alone will not provide adequate cleaning, they do not have grease or oil cutting properties to remove grime or hair and skin oils.
• Over time, the appearance and feel and performance of your upholstery may diminish if not cleaned properly.