Online since 2002 |   866-316-0162

Prism SGA-440 Sit to Stand Lift

Authorized Retailer

Prism SGA-440 Sit to Stand Lift is a smooth and versatile sit-to-stand lift, intended for clients who can participate actively in the transfer. Once in a standing position, transfer to a wheelchair or commode is done easily and smoothly. The client also gets valuable standing training with the transfer. It allows for a wide range of adjustments to the leg supports and the lifting bar itself to accommodate the support and comfort needs of the client. These adjustments enable the caregiver to adapt the raising to pain sensitive patients, residents or loved ones, or those paralyzed on one side, with no need for optional equipment or separate lifts.

Shipping charges applicable


  • Prism SGA-440 Sit to Stand Lift components:
    -SGA-440 Sit to Stand lift
    -Hand Control
    -Floor Lift Integrated Charger
    -Charger Cord
    -Owner Manual
    -Multi-Function Wrenches
    -5 mm Hex Allen Key (Short Arm)
    -4 mm Hex Allen Key (Short Arm)
    -3 mm Hex Allen Key (Short Arm)
  • Lightweight aluminum design offers stability and durability on a lightweight frame
  • Control box comes standard with diagnostic capabilities and can be used with your laptop for reporting and tracking of lift usage
  • Dual 3 x 3 casters offer the maximum control and smooth ride
  • Adjustable lifting bar allows settings for different-sized users
  • Leg support can be adjusted in width and height, plus the leg support and the foot rest can easily be removed when needed
  • The base width adjustment is easily done by a step/release bar at the rear of the lift
  • The SGA-440 Sit to Stand lift is a lifting aid used by health care professionals to transfer clients. The Sit to Stand lift makes it possible to move mobility impaired individuals with minimal strain or risk to the caregiver while providing complete safety, dignity and comfort for the client
  • The SGA-440 Sit to Stand lift is one of two components that make up this technology. The other component, the sling, is a specially designed fabric accessory that attaches to the floor lift by means of a carry bar and straps and holds an individual while the lift or transfer takes place. The sling is generally supplied with the Sit to Stand lift at the initial time of purchase
  • The SGA-440 Sit to Stand lift has the ability to lift an individual up from one location such as chair then move the individual to another location and finally lower the individual into a wheelchair. The functions of lifting up or down are accomplished by pressing buttons on the hand control. The hand control is attached to the Sit to Stand lift. Due to the design of the Sit to Stand lift system, it takes very little effort to press a button to perform the desired motion
  • Click Here for User Manual

More Information

  • Cautions:
    Under no circumstance should the SGA-440 Sit to Stand lift and sling (s) be put in control of a person who has not been properly trained in the use and care of this equipment. Failure to adhere to this warning may result in serious injury to the operator, and/or the individual being lifted/ transferred
    -The SGA-440 Sit to Stand lift and sling (s) are not toys. Do not use it for unsafe practices. Do not allow children to play with the floor lift or any of its components
    -The manufacturer warranty is voided if persons unauthorized by Prism Medical Ltd. will perform work on the SGA-440 Sit to Stand lift
    -There are no user serviceable parts inside the actuator. Do not remove cover screws, or open the unit, as this will VOID THE WARRANTY
    -Never expose the SGA-440 Sit to Stand lift directly to water. Warranty does not cover any misuse or abuse of the floor lift system
    -To maintain optimum function, the SGA-440 Sit to Stand lift should be inspected and maintained on a regular basis
    -Any accessories used with the SGA-440 Sit to Stand lift including sling (s), should be checked to ensure that they are in good working order. Check for signs of wear or fraying prior to use. Report any unusual wear, or damage immediately to your local authorized Prism Medical Service Provider
    -The SGA-440 Sit to Stand lift and associated sling (s) are intended only for lifting and transferring of a person. Prism Medical will not be responsible for any damage caused by the misuse, neglect or purposeful destruction of the lift, and/or its associated components
    -In any circumstances do not exceed the maximum allowable load of this lift
    -There is a risk of explosion if the lift is used in the presence of flammable anesthetics
    -Ensure that a clear space is maintained around the lift. Move any obstacles out of the way before operating the floor lift
  • Care:
    - Do charge the battery whenever possible. This will extend the battery life. A large number of cycles can be obtained from operating on the batteries, but battery lifetime is reduced with frequent discharging
    -Do inspect all cables particularly the mains power cable on the charger for any damage; replace where necessary
    -Do stow the handset and if fitted with charger, the mains power cable when transporting the hoist
    -Do clean the actuators, control box, charger, battery and handset at regular intervals to remove dust and dirt
    -The exterior of the lift should only be cleaned, disinfected and sterilized using isopropyl alcohol
    -Damp a cloth with isopropyl alcohol and wipe down entire exterior of lift
    -No other chemicals and/or liquids should be used to clean, disinfect and sterilize this lift
    -Do not allow the batteries to fully discharge before connecting to the charger. The batteries are a lead acid gel cell type that can be trickled charged continuously (batteries used for standby) and have a high current discharge capacity. Life is greatly reduced by deep or complete discharging of the batteries. Longer lifetime is obtained by maintaining fully charged batteries
    -Do not continue to operate the handset by repeatedly pressing the buttons if the lift function will not move or the actuator will not function. If this occurs then the actuator has either reached its end position, the load is too great or there is a malfunction
    -Do not exert excessive force on the handset cable as this may break off the wires inside the cable and prevent some or all of the operations
    -Do not continually operate the hoist functions. The system is not designed for continuous operation.Continuous Operation will cause batteries to be deeply discharged or to damage the actuator or control box by overheating


Technical Specifications:

Particulars Specification
Maximum weight capacity 440 lbs. (200 kg.)
Maximum lifting height 54.3 inches (138 cm)
Minimum lifting height 35.4 inches (90 cm)
Height to top of legs 4.3 inches (11 cm)
Clearance from bottom of legs to the floor 2 inches (5 cm)
Overall length 40.7 inches (103.5 cm)
Distance inside the legs (min.) 23 inches (58 cm)
Distance inside the legs (max.) 35 inches (89 cm)
Distance outside the legs (min.) 26.8 inches (68 cm)
Distance outside the legs (max.) 39 inches (99 cm)
Turning radius 46 inches (117 cm)
Wheels (dual-wheel castors) Front 3 (76 mm)
Rear  3 (76 mm) with brake
Weight of lift 81 lbs (36.8 kg.)

Electrical Specifications:

Particulars Specifications
Lift Motor 24 VDC, 10.5 Amps Max.
Charger Input 100-240 VAC, 50-60 Hz, 0.4 Amps Max.
Charger Output 24 VDC, 0.65 Amps
Batteries 24 VDC (2 x 12 VDC) 2.9 Ah, Sealed Lead Acid
Hand Control Electric
Lifting Range 35.4 to 54.3
Duty Cycle 10% use, 90% rest
Rated Performance 30 lifts at 440 lbs., 10% duty cycle




1 Year Warranty

Customer Reviews


{{x.ShortDescription}} ...


Please enter your and your friends email address below.

Fields marked with * are compulsory

Your Name*
Your Email Address
Friend's Name*
Friend's Email Address
The selected product information along with Reward Dollar coupon code has been successfully emailed to you and your friend.

Thank you for using