SOLE Softec Casual Footbeds

SOLE Softec Casual Footbeds

Brand/Manufacturer: SOLE


This product is on backorder and will be available to purchase once it is back in stock.

SOLE Softec Casual Footbeds has mouldable orthopedic base layer, plus 1.6mm layer of Softec cushioning, topped off with an ultra soft synthetic nubuck top sheet. Perforations are added to the forefoot to increase breathability. It is ideal for stylish casual footwear. It is also recommended footwear for casual and dress shoes and golf shoes.


  • SOLE Softec Casual Footbeds has tiny holes punched through the forefoot to increase air flow
  • Accepted by the American Podiatric Medical Association
  • Contains no animal products or byproducts
  • Medium thickness footbeds for most footwear
  • Custom orthopedic support
  • Equalized pressure distribution
  • Reduced plantar fascia strain
  • Increased balance and feel
  • Improved natural heel cushioning

More Information

  • Fitting instructions
    Choose one of two moulding methods for your new footbeds
    -Wear moulding is the simplest way to custom fit your new footbeds. Remove the factory sock liners from your footwear, insert your new SOLE Custom Footbeds and wear as with any other shoe. The footbed will adapt to your unique foot after a few days of regular use
  • HEAT MOULD -Heat moulding will provide the highest level of customization in the shortest amount of time. This is achieved by heating up the footbeds in an oven before placing them inside your footwear. To heat mould your footbeds, follow the steps listed below:
    -PRE-HEAT YOUR OVEN. DO NOT USE A MICROWAVE. CONVENTIONAL OVENS: Set to bake at 90ºC. FAN-ASSISTED OVEN: Start at 80ºC. GAS OVEN: Start at lowest gas mark
    -IF POSSIBLE, REMOVE THE FACTORY-SUPPLIED SOCK LINER FROM YOUR FOOTWEAR If the factory-supplied sock liner cannot be removed because it is permanently glued in, leave it in place
    -IF NECESSARY, TRIM YOUR NEW FOOTBEDS TO FIT Before you put your new footbeds in the oven, try them in your footwear to make sure they fit properly. If the footbed needs trimming, use the old sock liner as a guide. Make sure you only trim the toe end and be careful to not trim them too short
    -PUT YOUR FOOTBEDS IN THE PRE-HEATED OVEN FOR TWO MINUTES Place the footbeds in the oven on a baking sheet. Leave them in the oven for two minutes or until the Opti-therm indicator turns black. If the indicator has not turned black after three minutes, remove the footbeds. They will be ready to mould
    -REMOVE FROM THE OVEN AND IMMEDIATELY PLACE INSIDE YOUR FOOTWEAR Make sure the footbeds are laying flat in your footwear and have not bunched up
    -STEP INTO YOUR FOOTWEAR RIGHT AWAY Make sure your heels are against the back of the shoe. If your footwear has laces, lace them up as you normally would
    -STAND UP STRAIGHT AND HOLD YOUR POSITION FOR TWO MINUTES Stand with your feet shoulder-width apart and your toes pointed forward. As a guide, your knee cap should be directly over the top of your second toe. After two minutes, your footbeds will be moulded to your unique feet, providing personalized support and comfort so you can be and stay active
    -Diabetics and people with poor circulation or lack of sensation in their feet should consult their health care professional before using this product, to ensure appropriate treatment and care.


WEIGHT(half pair)10g to 64.9g (approx.)7g to 48.9g (approx.)

Width - Forefoot (approx.)

10mm to 98mm7mm to 87mm
Length - Heel to toe (approx.) 10mm to 290mm7mm to 245mm

Customer Reviews

Please enter your and your friends email address below.
Fields marked with * are compulsory


The selected product information along with Reward Dollar coupon code has been successfully emailed to you and your friend.

Thank you for using



Also available:

${{ x.OurPrice | currency: "" : 2}}

Articles & news

Related Articles


{{x.ShortDescription}} ...

Questions & Answers

Enter your Answer below.

Security Question: + =
question image
ItemName - now

Your question will show here once it will get approved.
answer image
UserName - now
Your Answer will show here once it will get approved.