Precision Medical PowerVac Aspirator
Precision Medical PowerVac Aspirator

Precision Medical PowerVac Aspirator

Brand/Manufacturer: PRECISION MEDICAL, INC
  • Made in USA

Precision Medical PowerVac Aspirator is used to supply a continuous vacuum source, within the stated operating vacuum range. It features a dual protection system that consists of a float shut-off in the canister lid and an Inline Hydrophobic filter to prevent back flow of fluid as well as airborne contaminants from entering the pump. It has a unique, moveable canister holder which allows the caregiver to rotate the canister to either side of the unit for better placement near the point of use.

Cannot be shipped Rush or Expedited delivery.

Item #DescPkgRewardPrice 
PM61 15-7/8"L x 7-3/8"W x 10-1/8"H (40.3cm x 18.7cm x 25.7cm) Each $22.50


  • Precision Medical PowerVac Aspirator includes:
    - Hospital grade power cord
    - 2000cc canister with lid
    - Adjustable canister holder
    - Hour meter
    - Protective filter
    - Durable infection control frinedly housing
  • ABS plastic cabinet is durable, attractive, easy-to-clean and infection control friendly
  • Safety is assured with the automatic resetting thermal limit switch which prevents the unit from overheating
  • High performance 1/5 horsepower pump delivers 0 to 26"Hg (0 to 660mmHg)
  • Compressor shelf is powder coated and durable
  • Pole, base arms and casters are smooth
  • Assured with the automatic resetting thermal limit switch which prevents the unit from overheating
  • Click here for User Manual

More Information

  • Operating Instructions:
    - Place Aspirator near a properly grounded electrical receptacle on a table, floor or other horizontal, smooth, hard surface. Allow a minimum of 4 in (10 cm) clearance on all sides to ensure adequate air flow for cooling of Aspirator.
    - Ensure the On/Off Switch and Selector Knob are in the “OFF” position.
    - Ensure the Inline Hydrophobic Filter is properly connected to the vacuum port on Suction Canister lid.
    - The Inline Hydrophobic Filter prevents liquid from entering the vacuum pump.
    - Plug the Aspirator into a properly grounded receptacle.
    - Press the On/Off Switch to the “On” position.
    - Block the patient connection on the Suction Canister and adjust the Vacuum Control Knob to the desired vacuum.
    To INCREASE vacuum - Turn knob CLOCKWISE
    - Vacuum should be set as prescribed by your Physician or Healthcare Professional.
    - Connect one end of Patient Suction Tubing to the port on the Canister marked Patient Tubing.
    - Connect other end of Patient Suction Tubing to suction catheter and begin procedure as instructed by Healthcare Provider.
    - When procedure is completed, press the On/Off Switch to the “OFF” position.
    - DO NOT overfill the canister.
    - Empty the Suction Canister as follows:
    - Disconnect all suctioning tubing.
    - Remove the canister from its bracket and empty as instructed by your Physician or Healthcare Professional.
    - Replace Suction Canister and reconnect all suctioning tubing.
  • Cleaning and  Maintenance:
    - The Inline Hydrophobic Filter cannot be cleaned. If it becomes contaminated or clogged, it must be replaced.
  • To replace Inline Hydrophobic Filter:
    - Disconnect filter assembly from Suction Canister and remove Suction Canister from the Aspirator
    - Remove filter assembly from the Aspirator
    - Dispose of filter
    - Install new filter (Part 1690) and reconnect tubing and elbow
    - Tubing is single patient use only. DO NOT clean
  • Cleaning for Exterior Components:
    - Disconnect the Aspirator from power source and other connections before cleaning
    - Use a cloth or sponge dampened with soap and water
    - Wipe dry with a clean cloth or paper towel
    - Store the Aspirator in a clean area free from grease, oil, and other sources of contamination


Length: 15.9" (40.3cm)
Width: 7.4" (18.7cm)
Height: 10.1" (25.7cm)
Unit Weight: 21lb (9.6kg)
Motor120VAC, 60Hz, 5Amps
Operating Vacuum Range0-622.3 mmHg (0-24.5 inHg)
Horsepower1/5 Horsepower
Storage Conditions
Temperature: -4°F. to 104°F. (-20°C. to 40°C.)
Humidity: Max 95% Non-condensing
Operating Temperature Range50°F. to 104°F. (10°C. to 40°C.)


3 year warranty

Customer Reviews

Questions & Answers


Enter your Answer below.

Security Question: + =
question image
ItemName - now

Your question will show here once it will get approved.
answer image
UserName - now
Your Answer will show here once it will get approved.
Please enter your and your friends email address below.
Fields marked with * are compulsory

The selected product information has been successfully emailed to your friend.

Thank you for using