Maddak Two Inches Contoured Tall-Ette Elevated Toilet Seat
Maddak Two Inches Contoured Tall-Ette Elevated Toilet Seat

Maddak Two Inches Contoured Tall-Ette Elevated Toilet Seat

Brand/Manufacturer: MADDAK, INC.
Save
Authorized Retailer Badge
  • HyGiene Products
  • Non Returnable

Maddak Two Inches Contoured Tall-Ette Elevated Toilet Seat has contoured surface which provides a more comfortable and supportive seat. Standard toilet seat comes with a Lok-In-El Slip-In Bracket that provides a fast, convenient and safe way to secure the seat. Elongated toilet seat comes with the Lok-In-El Bolt-Down Bracket that holds the elevated seat securely on elongated toilet bowls, full inner ring contact with the bowl is not required.

Cannot be shipped Rush or Expedited delivery.

Item #DescPkgRewardPrice 
F725831002 Elongated Each $3.15
$99.99
$62.99
F725841000 Standard Each $3.50
$99.99
$69.99

Features

Note : This item is non-returnable due to hygiene reason

More Information

  • How to Use:
    - Place the Tall-ette Elevated Toilet Seat upside down on a table or bench with its two bracket holes visible
    - Hold the Lok-In-El Bracket with the two pegs lined up with the holes on the seat
    - The bolt-down bracket tongue should be facing away from the seat
    - Press the pegs into the holes until the bracket is in place
  • To Install on Toilet (F725831002)
    - Loosen the nuts on the toilet seat bracket that hold the toilet seat and lid to the bowl. Be sure to loosen them enough to slide the Lok-In-El bracket between the seat and the bowl
    - Lift the toilet seat to a raised position and pull up slightly - approximately 3/8"
    - Slide the Lok-In-El bracket tongue under the seat bracket so that the wide section fits between the toilet seat screws and the two narrow sections fit outside of the screws
    - Tighten the nuts on the screws to secure the seat and bracket. The Tall-ette  Elevated Toilet Seat should be in contact with the china bowl with the bottom flange fitting inside the rim of the toilet bowl
    - Before tightening the screws, move the seat forward as much as possible to make sure the seat sits firmly in the bowl
  • To Install on Toilet (F725841000)
    - Lift the toilet seat to a raised position
    - Hold the Tall-Ette Elevated Toilet Seat so that the Lok-In-El bracket tongue points at a downward angle and slide the Lok-In-El bracket under the hinge pin between the bolts that hold the toilet seat in place
    - As the tongue slides into place, the Tall-Ette Elevated Toilet Seat should come to rest directly on the china bowl with the bottom flange fitting inside the rim of the toilet bowl
    - Now sit on the Tall-Ette Elevated Toilet Seat. The weight of your body will tighten the Lok-In-El brackets peg joint if it had not previously been seated completely
  • To Clean
    - Wash with a mild soap and water solution
    - Do not use commercial cleaners or bleaches, they may discolor the seat
    - If an antiseptic is desired, apply plain alcohol and wipe off promptly
  • Caution:
    Do not use these models without the Lok-In-El Bracket
    Do not remove the Lok-In-El Bracket
    Do not use the Tall-Ette Elevated Toilet Seat if it does not fit into the toilet bowl rim

Warranty

12 months parts and labor

Customer Reviews

Questions & Answers


 
 

Enter your Answer below.

Security Question: + =
question image
ItemQuestion
ItemName - now

Your question will show here once it will get approved.
answer image
UserAnswer
UserName - now
Your Answer will show here once it will get approved.
question image
Can I put my toilet seat lid on top of the Maddak Two Inches Contoured Tall-Ette Elevated Toilet Seat?
Ellen - 1/2/2017 11:18:23 PM
facebooktwitter
answer image
To Install on Toilet (F725831002)
 - Loosen the nuts on the toilet seat bracket that hold the toilet seat and lid to the bowl. Be sure to loosen them enough to slide the Lok-In-El bracket between the seat and the bowl 
- Lift the toilet seat to a raised position and pull up slightly - approximately 3/8" 
- Slide the Lok-In-El bracket tongue under the seat bracket so that the wide section fits between the toilet seat screws and the two narrow sections fit outside of the screws 
- Tighten the nuts on the screws to secure the seat and bracket. The Tall-ette Elevated Toilet Seat should be in contact with the china bowl with the bottom flange fitting inside the rim of the toilet bowl 
- Before tightening the screws, move the seat forward as much as possible to make sure the seat sits firmly in the bowl 

To Install on Toilet (F725841000)
- Lift the toilet seat to a raised position 
- Hold the Tall-Ette Elevated Toilet Seat so that the Lok-In-El bracket tongue points at a downward angle and slide the Lok-In-El bracket under the hinge pin between the bolts that hold the toilet seat in place 
- As the tongue slides into place, the Tall-Ette Elevated Toilet Seat should come to rest directly on the china bowl with the bottom flange fitting inside the rim of the toilet bowl 
- Now sit on the Tall-Ette Elevated Toilet Seat. The weight of your body will tighten the Lok-In-El brackets peg joint if it had not previously been seated completely.
Customer Care - 1/3/2017 6:36:37 AM
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*

 
SubmitCancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.healthproductsforyou.com

Close