Invacare Element Pneumatic Oxygen Conserver
Invacare Element Pneumatic Oxygen Conserver

Invacare Element Pneumatic Oxygen Conserver

Brand/Manufacturer: INVACARE CORPORATION
Save
Authorized Retailer Badge

Invacare Element Pneumatic Oxygen Conserver is capable of delivering a precise amount of supplemental oxygen at the optimal point in the breathing cycle. The conserver greatly increases the efficiency in the delivery of oxygen, maximizing the beneficial effects and eliminating unnecessary oxygen waste. It delivers consistent volume of oxygen with each breath, up to 40 breaths per minute.

Item #DescPkgPrice 
IOC100P 5"L x 2.5"H x 2.5"W Each $257.50 $172.99

Invacare Pneumatic Oxygen Conserver

Key Features:

  • 3.5 to 1 conserver with excellent pulse dose volumes
  • Excellent performance will keep patients saturated while extending the time of their cylinders
  • Senses a breath and delivers an oxygen bolus in first third of the inspiratory cycle
  • Single selector knob controls on or off, liter flow and continuous flow mode
  • Single lumen system
  • No batteries required
  • Conserving flow: Settings of 1 through 6
  • Continuous flow: 2lpm
  • Compatible with CGA 870 cylinders (not included)
  • Material: Aluminum
  • Color: Blue
  • Note: This product is to be used as an oxygen supplement and is not intended to be life supporting or life sustaining

Parts Description:

Invacare Element Pneumatic Oxygen Conserver  A. Cylinder Post Valve T-Handle Clamp
B. Cylinder Alignment Pins
C. Cylinder Gauge
D. Oxygen Supply Outlet Fitting
E. Vent Hole
F. Cylinder Gauge Needle
G. Selector Switch
H. CGA870 Seal Washer

Intended Use:

  • This oxygen conserving regulator is intended to be part of a portable oxygen delivery system for patients who require supplemental oxygen in their home and for ambulatory use
  • It is for patients who would normally receive the oxygen via a nasal cannula

Also Available (separately):

More On Pneumatic Oxygen Conserver

Installing the Conserving Regulator:

  1. Loosen the T-Handle on the conserving regulator device.
  2. Lower the conserving regulator device over any CGA870 post valve cylinder with the alignment pins toward the holes on the cylinder neck.
  3. Align the two pins and gasket with the corresponding holes on the cylinder post valve.
  4. While holding the unit in place, tighten the T-Handle on the conserving regulator device by turning clockwise.
  5. Attach a standard cannula (7 ft (2.1 m) or less in length) to the oxygen supply outlet fitting.

Removing the Conserving Regulator:

  1. Completely close the oxygen cylinder post valve.
  2. Turn the oxygen conserving regulator selector switch G to 2 L/min. continuous flow position.
  3. Wait for oxygen to stop flowing from the oxygen conserving regulator.
  4. Turn the conserving regulator to “Off”.
  5. Turn the T-Handle to loosen the connection to the post.
  6. Remove the oxygen conserving regulator from the post.

Cleaning Instructions:

  1. Ensure the cover is installed on the fillport.
  2. Clean exterior surfaces of the cylinder with a lint free cloth dampened with 70% isopropyl alcohol.
  3. Clean the exterior surfaces of the conserving regulator with a dry, lint free cloth.
  4. If the conserving regulator is still visibly soiled, clean with a lint free cloth dampened with 70% isopropyl alcohol. Do not wipe the fillport or outlet fitting.
  5. Wipe the cylinder and conserving regulator with a dry lint free cloth. Ensure the product is dry before using.

Specification

Particulars

Dimensions

Weight

14.8oz

Pulse Dose Volumes

Setting :  1, 2, 3, 4, 5, 6
ml O2 :   28, 43, 64, 78, 91, 103

Continuous Flow

2 L/min +/- 0.5

Required Operating Pressure

200 psi to 3000 psi

Savings Ratio

3.5:1

Cannula

Single lumen

Regulator

built-in 25 +/- 5 psi

Operating Temperature

32° F (0°C) to 122° F (50°C)

Operating Altitude

0 to 10,000 feet

                                        

Cylinder Duration Table
Cylinder TypeCylinder Volume (L)
SettingContinuous Flow
123456
Estimated Cylinder Duration in Hours
Based on 20 BPM
M2361.90.90.60.50.40.30.3
M41135.92.92.01.51.21.00.9
M61648.54.32.82.11.71.41.4
ML61718.94.53.02.21.81.51.4
M924612.86.44.33.22.62.12.1
D42522.111.17.45.54.43.73.5
E68035.417.711.88.97.15.95.7

 

Warranty

2 year limited warranty

Customer Reviews

Questions & Answers


 
 
question image
do I need a prescription for this device?
Label Atkinson - 10/7/2016 10:13:25 PM
facebooktwittergplus
answer image
Thank you for contacting customer care service. 
Yes, a prescription is required for this product
Customer Care - 10/8/2016 12:25:17 AM
question image
do you need a prescription for this device?
label atkinson - 10/7/2016 10:08:06 PM
facebooktwittergplus
answer image
Thank you for contacting customer care service. 
Yes, a prescription is required for this product
Customer Care - 10/8/2016 12:25:41 AM
question image
I need a new thumb screw.
arthur smith - 1/19/2016 7:13:57 AM
facebooktwittergplus
answer image
Unfortunately, we do not sell thumb screw.
Customer Care - 1/21/2016 12:05:29 AM
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*

 
SubmitCancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.healthproductsforyou.com

Close