Invacare HomeFill Oxygen Compressor


Invacare HomeFill Oxygen Compressor is designed to supply pressurized oxygen to fill Invacare proprietary gas cylinders for ambulatory use while the patient receives therapeutic oxygen from an accessory oxygen concentrator. It can fill cylinders for portable use by ambulatory patients.

Benefits of HomeFill Oxygen Compressor

  • Provides an unlimited, refillable oxygen supply 
  • Ensures oxygen purity is always greater than 90% 
  • Breathe from continuous flow oxygen concentrator at night 
  • Multiple cylinder sizes are available

Invacare HomeFill Oxygen Compressor Features

  • Patient breathes from a continuous flow oxygen concentrator at night
  • Patient protection ensures oxygen purity in cylinder is always greater than 90% 
  • No extra equipment needed because patients can breathe off concentrator while filling cylinders
  • HomeFill Oxygen Compressor provides an unlimited refillable ambulatory oxygen supply
  • Encourages compliance with oxygen therapy as patients have no worries about running out of oxygen
  • System is compatible with 5 liter or 10 liter concentrators and a wide variety of cylinder options (Concentrators and cylinders are not included)
  • Eliminating oxygen deliveries increases independence, convenience and comfort
  • Allows the patient to breathe at home from a continuous flow concentrator and then use a convenient ambulatory pack when they are “out and about.”

What does HomeFill Compressor Include?

  • Multistage compressor
  • Internal reservoir
  • Inlet fitting
  • Control electronics with an integral oxygen concentration sensor
  • Interlocking fill fitting
  • Drive motor

What to buy with Invacare Oxygen Compressor

How to use Oxygen Concentrator?

Connecting the Cylinder to the Compressor

  1. Examine the cylinder gauge. If the cylinder pressure is less than 1500 psig, proceed to Step 2.
  2. Set the regulator flow dial on the cylinder to Off
  3. Remove the cylinder and connector fillport covers (if present)
  4. Momentarily push Down on the outer ring (sleeve) of the connector fillport until Green dots are visible to reset the connector
  5. Grasp the cylinder in the area behind the cylinder fillport
  6. Position the cylinder in the compressor cradle
  7. Align the cylinder fillport with the connector fillport
  8. Pull Up on the outer ring (sleeve) of the connector fillport while pushing Down on the cylinder to couple the cylinder fillport into the connector fillport

Disconnecting the Cylinder from the Compressor

  1. Press the compressor power switch to the Off (O) position
  2. Grasp the cylinder in the area behind the cylinder fillport
  3. With the other hand, grasp the outer ring (sleeve) of the connector fillport and push Down F
  4. Lift up on the cylinder to remove from the connector fillport
  5. When the cylinder fillport is disconnected from the connector fillport, release the outer ring (sleeve) of the connector fillport and use two hands to remove the cylinder from the compressor cradle
  6. Place the fillport covers onto the connector fillport and cylinder fillport
  7. Examine the cylinder gauge to ensure cylinder is full (needle pointing into Green area). If the cylinder is not full, perform the following:
    • Repeat Connecting the Cylinder to the Oxygen Compressor
    • If cylinder is not full after second attempt to fill, contact the provider.

Turning the Oxygen Compressor On and Off

  1. Make sure the concentrator is On
  2. Set the concentrator flow rate to the patient to 3 L/min or less for Platinum 5, XL, and Perfecto2 and 5 L/min or less for Platinum
  3. Make sure the cylinder is connected to the compressor
  4. Push the power switch on the control panel to the On ( I ) position
  5. Examine the control panel. The following sequence of events should occur:
    • 0-3 minutes - The O2 Below Normal (YELLOW) light will be lit while the compressor warms up
    • After three minutes - The Filling (GREEN) light will be on while the cylinder is filling
    • The Full (GREEN) light will be on when the cylinder is finished filling
  6. Remove the full cylinder
  7. Push the power switch to the Off (O) position

Note: Image shown with cylinder which is not included

Invacare Compressor User Manual

HomeFill Oxygen Concentrator Specifications



Electrical Requirements

120 VAC ± 10% at 60Hz

Power Consumption

140 watts

Rated Current Input


Inlet Pressure Rating

14psi to 21psi

Oxygen Output (from concentrator)
5-liter Concentrator:
10-liter Concentrator:

0lpm to 3lpm (while filling cylinders)
0lpm to 5lpm (while filling cylinders)

Oxygen Input

0lpm to 2lpm


20.25"W x  15"H x 16"D


33 lbs

Cylinder Filling Times (average)

M2: 24 minutes, ML4: 55 minutes, ML6: 75 minutes, M6: 60 minutes, M9: 159 minutes, D: 3.5 hours

Invacare HomeFill O2 Compressor Warranty

1 year limited warranty on compressor, 3 year or 5000 hrs (whichever comes first) limited warranty on internal wear components (piston seals and rings, bearings, drive belts, check valves, pressure relief components and electric motor) and control panel.

Customer Reviews


ItemName - now     09/19/2021

  Your question will show here once it will get approved.

UserName - now     09/19/2021

  Your Answer will show here once it will get approved.



Annette     07/15/2016

Will this fill an E cylinder when attached to a Invacare Platinum XL?


Customer Care    07/19/2016

Thank you for contacting customer care service.

No the IOH200 will not fill the E cylinder it is to large.



Ralph     07/12/2016

Can I use the oxygen compressor without the oxygen concentrator if all I want to do is fill oxygen tanks?


Customer Care    07/15/2016

Thank you for contacting customer care service.

 It is not possible to use the compressor without a concentrator. There is an Oxygen sensor in the unit that stops filling if the oxygen purity drops below 90%



Robin     06/25/2016

How do you remove tank


Customer Care    06/27/2016

Thank you for contacting customer service. 

Please refer page no. 20 given on below link.


{{x.ShortDescription}} ...

What is HPFY’s return policy?

Customer satisfaction is our top priority. We stand behind our products. If the merchandise you received is defective or not what you expected it to be, and you wish to return the item, please submit a return request in the My Account section of our website, contact our Customer Service department at (866) 316-0162 / (203) 616-2850 or email us.

  1. Merchandise must be returned within 30 days of the receipt of your order. Returns are not accepted after 30 days.
  2. Items (including parts and accessories) must be returned in new, unused, and resalable condition in its original packaging.
  3. Before returning any product, the buyer must obtain a Return Authorization Number (RA#) from a customer service representative. With your RA# you will receive a prepaid return shipping label.
  4. Orders returned without obtaining an RA# will be entitled to receive only "In-Store Credit" that can be used towards future purchases.
  5. Return orders are subject to a 20% restocking fees.
  6. All custom orders and hygienic items are non-returnable. Refer to the “Non-Returnable Items” section for further details.
  7. Returns will be reviewed and inspected before issuing credit. Please allow 3 to 4 weeks for processing. The credit will be applied to your original method of payment.
  8. If the return is the result of a defective product or shipping error, we will refund the entire purchase amount and return shipping costs.

Which products are Non-Returnable?

Due to the hygienic nature of some items, they are non-returnable. The items listed below are non-returnable:

  1. All hygienic items.
  2. Opened personal care items.
  3. Anything opened, used, or tried on.
  4. All customized items.
  5. Besides these, items that have the “non-returnable” phrase on the website.

We reserve the right to make adjustments due to errors, changing market conditions, product discontinuation or typographical errors in advertisements. Images on the site may not always reflect the actual product. Footrests or leg-rests are not included with wheelchairs unless specified.

How do I receive a return authorization number?

You can submit a return request by logging into your account. You will receive the Return Authorization Number (RA#) details in the email within 2-3 business days.

  • Login to your account
  • Go to “order history”
  • Click on “return order”
  • Fill out the return form and Submit it

If you do not have an email address, we will make other accommodations for RA# Details. Write the RA# on your label affixed to your package prior to shipment.

How long does it take to receive a refund?

Please allow 3 to 4 weeks to process the returns. Once the item is received, and inspected, your refund will be processed and automatically applied to your credit card or original method of payment.

Is there any Restocking Fees?

  1. 20% restocking fees will be applied.
  2. Outbound shipping cost is non-refundable.
  3. For orders that qualified for free shipping, $8.99 will be deducted from the refund if the product is returned.

More Invacare Products

{{'Buy ' + x.Name}}
${{ x.OurPrice | currency: "" : 2}}
Please enter your and your friend's email address below.
Fields marked with * are compulsory

Submit Cancel
The selected product information along with Reward Dollar coupon code has been successfully emailed to you and your friend.

Thank you for using