Drive Wireless Bedside Alarm
Drive Wireless Bedside Alarm

Drive Wireless Bedside Alarm

Brand/Manufacturer: DRIVE MEDICAL
Save
Authorized Retailer Badge

Drive Wireless Bedside Alarm relies on infrared technology to detect motion. Alarm sounds when individual attempts to leave or falls out of bed. It is ideal for ICU or anywhere, where early detection is necessary. Invisible curtain of protection provides a wide area of protection and it installs easily with magnetic mount.

Item #DescPkgRewardPrice 
13601 Bedside Alarm Each $0.86
$118.55
$85.99

Features

  • Drive Wireless Bedside Alarm is great for use at home, in nursing homes or hospitals
  • Alarm emits an invisible fan-shaped beam that will cover an area approximately 60° horizontal and 6° vertical
  • Unit can be used as an alarm or warning device
  • Swivel bracket adjusts monitoring beam
  • One 9V battery (included)
  • No pads or clips to avoid false alarms
  • 85dB to 95dB without volume control

More Information

  • Installation:
    - Select proper mounting location based on area to be detected.
    - Carefully spread bracket open and remove unit.
    - Slide battery cover off and insert one 9-Volt battery, included. Ensure that battery contacts are securely snapped onto battery. Allow 20 seconds after battery installation before use.
    - Replace battery cover and secure unit in bracket. Orientate unit in bracket so that when unit is mounted, power switch faces away from patient (if possible) for easy access by staff or caregiver.
    - Position bracket for desired detection area and securely mount to wall, headboard, or magnetic bracket. Magnetic bracket is included when alarm with bed rail bracket is purchased. Swivel bracket is included for wall or headboard mounting with Alarm Only. Mounting screws not included.
    - Unit will only detect motion on side of bed it is mounted on. When vertically at side of bed, projected beam is perpendicular to the floor. When mounted above headboard horizontally, projected beam is parallel to mattress.
    - Perform test after installation to ensure proper function. Unit should chime/alarm when motion occurs in the desired detection area. Re-adjust position of unit if necessary to obtain proper When power is switched on, unit enters 10 second exit delay mode. When testing, wait 10 seconds before attempting to test for alarm/chime signal.
    - Detection beam extends up to 24 feet from unit. As false alarms can be triggered by caregivers or other patient, privacy curtains can be utilized to inhibit beam from extending beyond desired detection area. Example: When locating unit at headboard, place curtain at foot of bed.
  • To Test:
    - Test unit prior to every use to ensure proper function and battery power. Turn unit on and select ALARM or CHIME mode. When power is switched on, unit enters 10 second exit delay mode. Wait 10 seconds before attempting to test for ALARM/CHIME signal.
    - If ALARM/CHIME fails to sound and there are no obstructions in front of lens, replace battery immediately.
    - Waving hand in front of the unit may not consistently activate alarm/ chime. To accurately test, install product and simulate actual use. Alarm should sound when exiting bed.
  • Care
    Alarm Mode:

    - Turn unit on and select “ALARM” position. There is a 10 second exit delay to allow staff or caregiver to exit the room without activating alarm.
    - Once an object has penetrated the detector field, unit will alarm for 30 seconds from initial detection of motion and then automatically reset.
    - As long as sensor continues to detect motion in the detector field, unit will alarm.
    Chime Mode:
    - Turn unit on and select “CHIME” position. There is a 10 second exit delay to allow staff or caregiver to exit the room without activating chime.
    - Once an object has penetrated the detector field, unit will chime for 30 seconds from initial detection of motion and then automatically reset.
    - As long as the sensor continues to sense motion in the detector field, unit will chime. 
  • Care and Maintenance:
    - Check unit before each use to ensure function. If motion fails to activate unit, replace battery.
    - If unit fails to work with new battery, check and clean battery terminals.

Warranty

1 Year limited warranty

Customer Reviews

Questions & Answers


 
 
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*

 
SubmitCancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.healthproductsforyou.com

Close