(Brondell FreshSpa Easy Bidet Toilet Attachment)-Discontinued

Brondell FreshSpa Easy Bidet Toilet Attachment Features

• Hygienic retractable nozzle
• Self cleaning nozzle feature
• Ambient temperature bidet wash
• Nozzle positioning (3 settings)
• Adjustable water pressure All brass internal valve
• High quality metal 7/8” T-valve
• High quality braided metal hose
• Anti-bacterial ABS material with full body panel
• Backflow prevention valve
• No electricity or batteries required
• Easy installation and adjustable toilet fit
• All accessories included for standard installation

FreshSpa Bidet Toilet Attachment Parts

• Bidet attachment with turn dial control
• Adjustable brackets
• T-valve connector
• Bidet hose
• 2 ea large rubber washers
• 1 ea small rubber washer
• 1 ea small rubber washer with raised lip

 

What to buy with Bidet Toilet Attachment

• Brondell Swash Bidet Water Filter
• Cleanis Carebag Commode Liner with Super Absorbent Pad
• Etac Torkel Toilet Paper Tong

How to install FreshSpa FS-10?

1. Remove existing toilet seat -
   • Lift hinge covers and use flathead or Phillips head screwdriver to remove the mounting bolts. Alternatively, you may need to loosen mounting bolts underneath the seat.
   • Remove the toilet seat and set the seat, mounting bolts and hardware aside.
2. Turn off water supply valve and flush toilet -
   • Turn off water supply at the wall to stop flow of water.
   • Flush toilet and hold down handle to completely empty toilet tank
   • Disconnect water supply hose from the fill valve under the toilet tank
3. Connect 7/8” T-Valve to Water Supply Line and Fill Valve Under Toilet Tank - 
   • Install the 7/8” T-valve with the small rubber washer with raised lip to the incoming water connection on the bottom of your toilet tank. Be sure to place the flat edge of the rubber washer into the T-Valve against the metal with the raised lip facing the toilet tank connection.
   • Connect the cold water supply line coming from the wall to the bottom of the T-valve using the small flat rubber washer (if needed).
4. Connect Bidet Hose to T-Valve - Connect one end of the metal Bidet Hose to the remaining open side of the installed 7/8” T-valve
5. Install Bidet Attachment on Toilet - 
   • Place large rubber washers over the open bolt holes in the toilet fixture
   • Place bidet attachment over washers so the nozzle is as close to the back of the toilet bowl as it will go. This will vary by toilet.
   • Make sure the adjustable brackets line up with the holes in the toilet fixture. You may need to move the adjustable brackets accordingly to line up properly.
   • Replace the toilet seat on top of bidet attachment and secure using original toilet seat hardware. Make sure to tighten so that the bidet attachment and seat do not move.
6. Connect Bidet Hose to Bidet Attachment - Connect open end of bidet hose to the brass connection on the bottom side of the bidet attachment
7. Turn on Water Supply & Check for Leaks - Open the main water supply valve slowly and check for leaks. b. Wait 5-10 minutes, check again and if there are no leaks continue.
   Note - If there is any leaking, check all rubber washers and make sure all water connections are tight and secure. If necessary, you can use plumbers tape for any leaking connections.

How to operate Brondell FreshSpa?

• Using the FreshSpa - To clean the bidet nozzle, turn the control dial towards the “Nozzle Cleaning” position and water should wash over the nozzle. For the general bidet wash function, turn the dial towards the “Wash” position.
  • The further the dial is turned, the higher the water pressure will be
  • To lower the water pressure, turn the nozzle back towards the center
  For a front wash function, women may need to tilt & bend forward slightly in order for the spray to hit the appropriate areas.
• Nozzle positioning- There are 3 different nozzle positions that you can easily adjust by gently pulling the end of the nozzle forward or backwards. Once desired position is set, the nozzle will remain in that position until manually moved.

FreshSpa FS-10 Bidet Maintenance

• To clean the nozzle, gently pull down on the head of the nozzle, and use a toothbrush or soft cloth and mild detergent (such as dish soap) to clean the nozzles
• You may also unscrew the nozzle tip cap for a more thorough cleaning or use a toothpick if any nozzle holes are plugged with hard water buildup
• To clean the bidet, use a mild cleaner to clean the FreshSpa
• Do not scrub or use harsh, abrasive products to clean the FreshSpa, which may scratch the product.

Brondell FreshSpa Easy Bidet Toilet Attachment User Manuals

• Brondell FreshSpa Easy Bidet Toilet Attachment User Manual
• FreshSpa Bidet Toilet Attachment Specifications
• FreshSpa FS-10 Attachment Installation Guide