Battery Power Solutions Freedom CPAP Battery Kit For Respironics DreamStation

Battery Power Solutions Freedom CPAP Battery Kit For Respironics DreamStation is available in single and dual battery. It is perfect for camping, airline travel, and used as a backup power supply during power outages so your PAP therapy will continue uninterrupted. The easy-to-read digital display screen shows remaining charge level and it charges to full capacity in 4 hours (per battery) when completely discharged. Meets FAA requirements for lithium-ion batteries taken in carry-on baggage during air travel.

Features

• Battery Power Solutions Freedom CPAP Battery Kit For Respironics DreamStation includes:
  - Freedom CPAP Battery
  - DreamStation 12V power adapter
  - AC power supply
  - DC power pigtail cord
  - Connector tips
  - DC input cord
  - Users manual
• DC power pigtail cord that allows two batteries to be pigtailed together to increase run times
• Features a 5V USB port for charging other small electronic devices such as cell phones, MP3 players and tablets
• Perfect solution for remaining compliant with your PAP therapy when enjoying your favorite outdoor activities, taking adventures on the road, or riding the high seas
• With the addition of the Auto Charge DC Cable or Sine Wave Power Inverter you can charge the Freedom in a vehicle, or with the addition of the SunPower 40W Solar Panel you can charge it using the power of the sun
• Power Outages:
  - Never worry about sleepless nights without your PAP therapy during power outages
  - Simply plug the FreedomTM CPAP Battery into the wall outlet and connect your PAP device to the battery
  - When AC power is available it will bypass the battery cells to power your device but during an outage, the battery will recognize the loss of AC power and automatically begin powering your PAP device
• PAP Device Compatibility:
  -Respironics DreamStation series devices via the included 12V power adapter
  - Also compatible with Respironics System One, Respironics M Series and Devilbiss IntelliPAP series devices via the included connector tips and DC power pigtail cord
• Estimated Run times:
  - The FreedomTM CPAP Battery will power a Respironics System One, Respironics M Series or Devilbiss IntelliPAP series device for
  - Single Battery: 1-2 nights
  - Dual Battery: 2-4 nights
  - Run times are estimates and depend upon several factors including PAP device type, pressure setting, and humidifier usage
  - All run times are based on CPAP devices without the use of heated humidification or heated tubing on a pressure setting of 10 cm/H2O
• Color:
  - Freedom CPAP Battery: White and Silver
  - Battery Kit Components: White
  - 12V Power Adapter: Black
• Dimensions:
  - Freedom CPAP Battery: 7.5"L x 4.8"W x 0.8"H, 1.7lbs
  - Respironics DreamStation 12V Power Adapter: 60"L (end to end), 4oz
  Note:
  - Use of heated humidification and heated tubing will reduce run times by two-thirds in most cases and in some cases could prevent the battery from being able to power the PAP device.
  - For optimal CPAP Battery performance, you should plan to use your machine without heated humidification or heated tubing.
  - BiPAP and AutoPAP machines will have lower run times as the pressure setting is not constant and changes throughout the night requiring more power to operate the machine.
  - Some older obsolete PAP devices and targeted ventilation PAP devices may not be compatible or may require more power than the FreedomTM CPAP Battery can provide.
  - Click Here for User Manual
  - Click Here for MSDS

More Information

• Connection Instructions:
  DeVilbiss IntelliPAP Series: Single Battery Connection
  - DeVilbiss IntelliPAP series devices can be connected directly to the Freedom CPAP Battery using the DC power pigtail cord and appropriate connector tip included in the Freedom CPAP Battery Kit.
  - Plug the DC power pigtail cord into the DC OUT jack of the battery.
  - Insert the connector tip with blue top labeled J into the DC power pigtail cord.
  - Plug the DC power pigtail cord with J connector tip attached into the DC input port of the PAP device.
  - Turn the PAP device on and it should begin functioning.
  - The digital display screen will show the charge level of the battery. You may press the charge level indicator button to illuminate this screen. It will stay illuminated for a few seconds at a time.
  - When not in use disconnect all devices from the battery thus allowing the battery to completely shut down.
  DeVilbiss IntelliPAP Series: Dual Battery Connection
  - Plug the DC power pigtail cord into the DC OUT jacks of both batteries.
  - Insert the connector tip with blue top labeled J into the DC power pigtail cord.
  - Plug the DC power pigtail cord with J connector tip attached into the DC input port of the PAP device.
  - Turn the PAP device on and it should begin functioning.
  - The digital display screen will show the charge level of the battery. You may press the charge level indicator button to illuminate this screen. It will stay illuminated for a few seconds at a time.
  - When not in use disconnect all devices from the battery thus allowing the battery to completely shut down.
  Respironics M & System One Series: Single Battery Connectiones
  - Respironics System One and M series devices can be connected directly to the FreedomTM CPAP Battery using the DC power pigtail cord and the appropriate connector tip included in the Freedom CPAP Battery Kit.
  - Plug the DC power pigtail cord into the DC OUT jack of the battery.
  - Insert the appropriate connector tip into the DC power pigtail cord.
  - System One 60 Series: Tip with black top labeled W
  - System One 50 Series & M Series: Tip with yellow top labeled N
  - Plug the DC power pigtail cord with appropriate connector tip attached into the DC input port of the PAP device.
  - Turn the PAP device on and it should begin functioning.
  - The digital display screen will show the charge level of the battery. You may press the charge level indicator button to illuminate this screen. It will stay illuminated for a few seconds at a time.
  - When not in use disconnect all devices from the battery thus allowing the battery to completely shut down.
  Respironics M & System One Series: Dual Battery Connection
  - Plug the DC power pigtail cord into the DC OUT jacks of both batteries.
  - Insert the appropriate connector tip into the DC power pigtail cord.
  - System One 60 Series: Tip with black top labeled W
  - System One 50 & M Series: Tip with yellow top labeled N
  - Plug the DC power pigtail cord with appropriate connector tip attached into the DC input port of the PAP device.
  - Turn the PAP device on and it should begin functioning.
  - The digital display screen will show the charge level of the battery. You may press the charge level indicator button to illuminate this screen. It will stay illuminated for a few seconds at a time.
  - When not in use disconnect all devices from the battery thus allowing the battery to completely shut down.
  Respironics DreamStation Series: Single Battery Connection
  - The DC input port on Respironics DreamStation series devices require a proprietary signal in order to recognize a valid power source; therefore, the use of a 12V power adapter is required in conjunction with the Freedom CPAP Battery.
  - Plug the 12V power adapter into the DC OUT jack of the battery.
  - Plug the 12V power adapter into the DC input port of the PAP device.
  - Turn the PAP device on and it should begin functioning.
  - The digital display screen will show the charge level of the battery. You may press the charge level indicator button to illuminate this screen. It will stay illuminated for a few seconds at a time.
  - When not in use disconnect all devices from the battery thus allowing the battery to completely shut down.
  Respironics DreamStation Series: Dual Battery Connection
  - Plug the 12V power adapter into the DC power pigtail cord.
  - Plug the DC power pigtail cord into the DC OUT jacks of both batteries.
  - Plug the 12V power adapter into the DC input port of the PAP device.
  - Turn the PAP device on and it should begin functioning.
  - The digital display screen will show the charge level of the battery. You may press the charge level indicator button to illuminate this screen. It will stay illuminated for a few seconds at a time.
  - When not in use disconnect all devices from the battery thus allowing the battery to completely shut down.